Abstract
Larix spp., a wood species of low dimensional stability, was heat-treated in nitrogen at 180 to 210 °C for 6 h. Changes in the thermal decomposition and combustion behaviors of the wood after heat treatment were investigated by TGA, SEM, FTIR, and cone calorimetry. TGA confirmed the loss of hemicellulose from heat-treated Larix spp. Small cracks in the cell wall and loss of resin from the vessels of heat-treated wood were observed by SEM. Hemicellulose degradation within the heat-treated samples was indicated by decreased intensities of typical O-H and C=O stretching vibration peaks in the FTIR spectra. The HRR and MLR curves of treated wood were much lower than those of the untreated ones, which is preferable for fire safety. However, the time to ignition of treated samples decreased from 22 to 13 s and the total smoke production increased by 4.76 and 43.3% for 180- and 210 °C-treated samples, respectively, a detrimental effect on fire safety. To determine the influence of heat treatment on the combustion behaviorof Larix spp., the fire safety properties of heat-treated wood (such as wood structure building, furniture, and floors) must be studied further.
Download PDF
Full Article
Effects of Heat Treatment on Thermal Decomposition and Combustion Performance of Larix spp. Wood
Dong Xing and Jian Li*
Larix spp., a wood species of low dimensional stability, was heat-treated in nitrogen at 180 to 210 °C for 6 h. Changes in the thermal decomposition and combustion behaviors of the wood after heat treatment were investigated by TGA, SEM, FTIR, and cone calorimetry. TGA confirmed the loss of hemicellulose from heat-treated Larix spp. Small cracks in the cell wall and loss of resin from the vessels of heat-treated wood were observed by SEM. Hemicellulose degradation within the heat-treated samples was indicated by decreased intensities of typical O-H and C=O stretching vibration peaks in the FTIR spectra. The HRR and MLR curves of treated wood were much lower than those of the untreated ones, which is preferable for fire safety. However, the time to ignition of treated samples decreased from 22 to 13 s and the total smoke production increased by 4.76 and 43.3% for 180- and 210 °C-treated samples, respectively, a detrimental effect on fire safety. To determine the influence of heat treatment on the combustion behavior of Larix spp., the fire safety properties of heat-treated wood (such as wood structure building, furniture, and floors) must be studied further.
Keywords: Heat-treated wood; Thermo-gravimetric analysis; Mass loss rate; Heat release rate; Smoke production
Contact information: Key Laboratory of Bio-Based Material Science and Technology, Northeast Forestry University, Ministry of Education, Harbin, China; *Corresponding author: nefulijian@163.com
INTRODUCTION
Wood is a sustainable natural resource widely used as a building material and for flooring, furniture, and interior decoration due to its intrinsic properties and relatively low price. However, wood has some negative characteristics that may need to be improved. For instance, some applications may require higher biological durability and better dimensional stability.
Heat treatment research began in the 1920s, when the swelling and shrinkage properties of heat-treated wood were evaluated. The durability of heat-treated wood was investigated in the 1940s using different shielding gases. In recent years, heat treatment processes have been achieved through process conditions variations such as the duration and temperature of the treatment, the type of heating atmosphere, the pressure, and the catalysts used. Heat treatment processes have provided the basis for growth of prosperous companies in European countries including Thermo-Wood in Finland (Shi et al. 2007), PLATO-Wood in Holland (Tjeerdsma et al. 1998), Ratification in France (Candelier et al.2013), and Oil Heat Treatment in Germany (Tjeerdsma and Militz 2005). Heat treatment improves the dimensional stability, aesthetic appearance, hygroscopicity, durability, and weather resistance (Huang et al. 2012; Yildiz et al. 2006; 2011) of wood and is an environmentally friendly process (Heigenmosera et al. 2013; Kamdem et al. 2002). The main components of the wood are modified by high-temperature treatments, in particular, pyrolysis of amorphous polysaccharide (hemicelluloses) and the condensation and crosslinking reactions of lignin (Kasemsiri et al. 2012; Korkut et al. 2008; Rowell et al. 2009) take place.
Heat-treated wood is still sensitive to flames (Delichatsios et al. 2003; Ondrej et al. 2001). However, it is widely used as an indoor and outdoor structural material and for decorations. Heat treatment releases low molecular weight, volatile compounds from wood and degrades polysaccharides and lignin, which are related to the thermal pyrolysis, flammability, and smoke release properties of the wood. The fire safety of heat-treated wood has rarely been studied.
The main purpose of this study was to investigate the effect of heat treatment on wood’s pyrolysis behavior and flammability performance via parameters such as the ignition time, heat release rate, mass loss rate, and smoke emission. Thermogravimetric analysis, SEM, FTIR, and CONE calorimetry were used.
EXPERIMENTAL
Wood Sample Preparation and Heat Treatments
Twelve-year-old Larix spp. was purchased from the Harbin timber market. Larix spp. is a softwood species planted heavily across northern and eastern China. It has wide adaptability, a long growing season, and high growth rates.
Wood blocks measuring 100 x 100 x 8 mm in the longitudinal, radial, and tangential directions according to ISO 5660-1, respectively, were cut and oven-dried at 103 °C (for approximately 48 h) before heat treatment. Twelve fine (free from defects) samples were randomly selected to be oven-dried. Four samples were left without heat treatment, while the remaining 8 samples were heat-treated. The blocks to be subjected to heat treatment were enclosed in an oven under a nitrogen atmosphere at 180, 190, or 210 °C for 6 h and treated by a thermal process used in furniture and structural wood factories. The temperature was controlled with an accuracy of ±1 °C. Next, each specimen was conditioned at a temperature of 30±1 °C and a relative humidity of 65±1% until testing. The whole blocks were ground and sieved to obtain particles between 0.2 and 0.3 mm in diameter for TGA (Thermogravimetric analysis) and FTIR analysis.
Analytical Instruments
To investigate the decomposition behavior of the heat-treated wood in this study, a Perkin Elmer Pro-6 TGA system (State of Connecticut, USA) with a nitrogen atmosphere was used. The system was heated from the ambient temperature to 800 °C at a heating rate of 10 °C/min with a nitrogen flow 25 mL/min for all pyrolysis experiments with 2 replications. The mass loss rate of each sample was recorded by the TGA system.
Four blocks of dimensions 8×8×2 mm cut from heat-treated blocks were sputter-coated (BAL-TEC SCD 005) with a gold layer for 140 s and were mounted on standard aluminum stubs with a conductive paste. The samples were scanned using an FEI Quanta 200 Scanning Electron Microscope (Hillsboro, Oregon 97124 USA) at an accelerating voltage of 10 kV. The temperature was approximately 20 °C and the column vacuum was 0.83 mm Hg (absolute).
After grinding, samples were dried at 105 °C for 24 h before pellet preparation. The samples were analyzed by FTIR (Magna-IR 560 E.S.P, Nicolet Company, USA) at a resolution of 4 cm-1 for 40 scans.
Fire safety tests were performed with a cone calorimeter (FTT Company, UK) according to ISO 5660-1(cone calorimeter) at a heat flux of 50 kW/m2, corresponding to a temperature of 760 °C. The four samples that were prepared and heat-treated before (100 x 100 x 8 mm) were fixed to a horizontal sample retainer and were protected by a stainless steel mesh to prevent sample bending or extension during testing.
RESULTS AND DISCUSSION
Thermal Decomposition by TGA
Thermogravimetric analysis results for untreated and heat-treated wood in a pure nitrogen atmosphere are presented in Fig. 1 and more detailed data are listed in Table 1. Figure 1 shows the thermal degradation behaviors of the wood flour used in this study. A peak in the first stage was observed with the gasification of moisture in the wood (Fujii et al. 2011; Almeida et al. 2008), which is a familiar feature of other lignocellulosic materials (Das et al. 2000). With increasing intensity of the heat treatment, the mass loss in this stage gradually decreased, which is in line with the results of the moisture study of heat-treated wood.
Fig. 1. TGA curves of heat-treated and untreated wood: a) untreated wood; b) heat-treated wood at 180 °C; c) heat-treated wood at 190 °C; and d) heat-treated wood at 210 °C
Table 1. Thermogravimetric Analysis Data under a Pure Nitrogen Atmosphere
The pyrolysis temperatures of hemicellulose (200 to 300 °C), cellulose (300 to 400 °C), and lignin (200 to 900 °C) are well-known. In the second stage (from 180 to 390 °C), the maximum mass loss rate appeared at a temperature of about 350 °C (see Table 1), corresponding mainly to the pyrolysis of amorphous hemicellulose and cellulose into char residues and the evaporation of the products (CO2, CO, CH4, CH3OH, and CH3COOH) (Becidan et al. 2007; Varhegyi et al. 1997).
The mass loss of untreated wood was 67.7% after the second main stage, larger than that of the heat-treated samples. This was attributed to the main decomposition process. However, the samples treated at 180, 190, and 210 °C did not have similar peaks at 320 °C in their respective TGA curves. This demonstrated that the heat treatments intensively degraded hemicellulose (Hosoya et al. 2007). The pyrolysis of cellulose began in the same stage as hemicellulose degradation (Yang et al. 2007; Zhang et al. 2012; Patwardhan et al. 2010). The highest decomposition intensity and the total degradation of cellulose appeared between 180 and 399 °C with a maximum rate at approximately 350 °C for all samples.
In the third stage, a similar peak, corresponding to lignin degradation, was observed for all samples (Eseltine et al. 2013). Lignin is one of the components of wood with the best heat-resisting ability (Garcia et al. 2008; Hosoya et al. 2006). According to the comparison of samples obtained in TGA experiments, heat-treated wood had greater mass loss in the third stage, which was partly caused by a higher ratio of lignin in the heat-treated wood. During the pyrolysis process, the breakage of 1-4 glycosidic bonds shortened cellulose chains, but sinistral glucose decomposed later (Hosoya et al.2007; Gua et al. 2013). The degradation activation energy needed for hemicellulose was much less than that for well-crystallized cellulose (Raveendran et al. 1996). Within the range of 180 to 550 °C, the wood weight loss rate was about 90%, indicating that the major components of the wood were pyrolyzed and only a small amount of residual cellulose remained. Because of the strong chemical stability of the propyl-benzene derivatives in lignin, its thermal decomposition took place over a relatively higher temperature and with slower reaction compared with cellulose and hemicellulose.
SEM Observations
SEM observations of cross-sections of wood samples show the anatomical structures of untreated Larix spp. (Fig. 2a), wood heat-treated at 190 °C (Fig. 2b), and wood heat-treated at 210 °C (Fig. 2c). Similar to the untreated Larix spp., the heat-treated wood maintained a stable cellular structure, while the high-temperature treatment caused some damage to the cell walls of the Larix spp. sample, as highlighted in Fig. 2. Most of the cell wall in the heat-treated samples had some deformations such as tracheid collapse and cracks. Comparing Figs. 2(a), (b), and (c), it is clear that the early wood tracheids of wood heat-treated at 190 °C remained intact, while the late wood tracheids gained several small cracks. The damage was much clearer in samples heat-treated at 210 °C. In the untreated sample, the resin canal of untreated Larix spp. was blocked by extractives. In the sample heat-treated at 190 °C, the extractives leaked partially out of the canal, forming a cavity. As shown in Fig. 2, the extractives of the canal in the sample heat-treated at 210 °C were completely evaporated.
Fig. 2. Scanning electron micrographs of wood samples: a) untreated wood; b) heat-treated wood at 190 °C; and c) heat-treated wood at 210 °C
The findings from the SEM micrographs are supported by the TGA of the heat-treated samples previously discussed. The modification of the wood cell wall appeared to be as a result of the degradation of hemicellulose and the leakage of extractives due to the high-temperature treatment (Nuopponen et al. 2004). These observations demonstrate that the cell wall structure became increasingly loose and fragile with increasing treatment temperature (Duygu and Sudeshna 2012; Priadi and Hiziroglu 2013; Li et al. 2013). As with the observations made via TGA, it is apparent that the hemicellulose in heat-treated wood was hydrolyzed, causing cracks in the cell wall (Priadi and Hiziroglu 2013). The loss of cell wall substances of heat-treated Larix spp. can also be confirmed from this finding.
FTIR Analysis
The results of the FTIR analysis of untreated and heat-treated Larix spp. wood samples are presented in Fig. 3 in order to investigate the structural and chemical component changes of the samples following heat treatment. The differences in the spectra of untreated and heat-treated wood were taken into consideration.
The characteristic bands of FTIR absorption in the region of 500 to 4000 cm-1 for both untreated and heat-treated wood are listed in Table 2. In general, due to the composition changes of thermally-modified wood, the FTIR peaks can change (Hakkou et al. 2005; Colom et al. 2003; Şen et al. 2012). In Fig. 3, the peak at 3335 cm-1 corresponds to O-H stretching vibrations; this peak’s intensity gradually decreased with increasing treatment temperature, making the heat-treated wood less hydrophilic (Huang et al. 2012). The reduction of the abundant hydroxyl groups present in hemicellulose from the FTIR spectra indicates the degradation of hemicellulose in heat treated-wood. This loss of hemicellulose from the cell wall is believed to have caused the cracks observed in the SEM images already shown. The peak between 1700 and 1750 cm-1 corresponds to C=O groups and is due to the conjugated ketone and carboxylic acid groups in lignin and hemicellulose (Evans et al.1991). The intensity of this peak decreased, which provides information about the chemical reactions taking place during heat-treatment. This could be due to the cleavage of acetyl side chains or the decomposition and evaporation of fatty acid esters, of which the ester and carboxyl groups are the most abundant functional groups of hemicellulose. With the exception of the sample treated at 180 °C, the peak at 1716 cm-1 corresponds to pyrolysis byproducts (Singh et al. 2013) such as carboxylic acids. These acids can accelerate hemicellulose degradation by catalyzing hydrolysis (Alén et al. 2002). The peaks at 1592 and 1504 cm-1 correspond to the carbon skeleton vibration of benzene rings in lignin (González et al. 2009). The intensity of these peaks increased with heat treatment, likely because of hemicellulose degradation and the increasing proportion of lignin. The decrease in intensity of the carbonyl band at 1264 cm-1 was slight. The intensity of the peak decreased markedly only when the treatment temperature exceeded 200 °C. This demonstrated the cleavage of acetyl groups in the hemicelluloses which is in accordance with the results of the TGA study previously discussed. The peak at 895 cm-1, corresponding to anti-symmetric, out-of-phase stretching of cellulose, started to diminish due to the depolymerization of hemicellulose (Risto et al. 2000).
Fig. 3. Fourier transform infrared (FTIR) spectra of one untreated and three heat-treated wood samples
Table 2. Characteristic Bands of FTIR Absorption in the Region 500 to 4000 cm-1 for Untreated and Heat-Treated Wood
Combustion Performance Test
The Cone Calorimeter was expected to effectively evaluate fire performance properties such as fire degradation, smoke emission, and heat release (Scudamore et al. 1991) of the tested materials.
The TTI (time to ignition), HRR (heat release rate), and THR (total heat release) are important parameters for evaluating the combustion of biomaterials, whereas the MLR (mass loss rate), SPR (smoke production rate), and TSP (total smoke production) can reveal the extent of mass loss and smoke expression during combustion. The representative MLR, HRR, SPR, and TSP versus time curves describe the combustion and smoke emission behaviors of heat-treated wood, as shown in Figs. 3, 4, 5, and 6 and Table 3.
Table 3. Influence of Heat Treatment on Wood Combustion
Fig. 4. Mass loss rate (MLR) curves for untreated and heat-treated samples
Mass loss rate (MLR)
The thermal decomposition behavior of the mass loss rate reflects the combustion process and is related to the heat release rate and smoke production. The heat treatment was a mild pyrolysis that did not change the tendency of the MLR curves. According to Table 3 and Fig. 4, Larix spp. pyrolysis reaction processes can be divided into two stages under a radiation intensity of 50 kW/m2.
The first stage of the MLR curves was mostly due to the elimination of moisture from the wood. From Fig. 4, it can be seen that heat-treated wood contained less moisture than untreated wood, which is in agreement with the research regarding the moisture content of heat-treated wood. The second stage of the thermal decomposition process mostly involved the combustion of major wood components, including cellulose, hemicellulose, and lignin.
The results of MLR analysis demonstrated that the heat-treatment significantly influenced the thermal decomposition behavior of the wood. At the beginning of the burning process, the MLR curves were only slightly different, but in the second stage, the peak MLR of all heat-treated wood samples appeared earlier and the peak values were lower than in the untreated wood. The second-stage peaks of 180-, 190-, and 210 °C-treated wood were reduced by 11, 15, and 46%, respectively, compared to those of the untreated wood. This suggests that the extractives of the heat-treated samples were partly released, that the hemicellulose was degraded, and that the char residue content increased during heat treatment (Hosoya et al. 2008; Patwardhan et al. 2011). The MLR of the sample heat-treated at 210 °C was reduced in both stages under a radiation intensity of 50 kW/m2, which demonstrated that the hemicellulose was fully degraded, the extractives were evaporated, and the moisture content was reduced (Yildiz et al. 2006). This is in agreement with the results of FTIR analysis and TGA. The condensation and crosslinking reactions of lignin during heat treatment promoted char residue formation, facilitating earlier carbonation during combustion. Earlier-appearing and lower peak MLR values indicated that the heat treatment was favorable for the wood’s fire safety.
Heat release rate (HRR)
The HRR is one of the major parameters measured in a Cone calorimeter. It is considered to be the most important parameter used to assess a material’s burning behavior (Fang et al. 2013).
Fig. 5. Heat release rate (HRR) curves for untreated and heat-treated samples
From Table 3, the TTI of the heat-treated samples was dramatically reduced, from 24 to 13 s, which caused combustion to occur earlier than in untreated wood. From Table 3 and Fig. 5, although the TTI appeared in a shorter time, the HRR of the heat-treated wood was significantly reduced during the combustion process. The 300-s average HRR (av-HRR) and peak HRR (pk-HRR) values of heat-treated wood were about 23 and 42% lower than those of untreated wood, respectively. A lower pk-HRR is preferable to reduce the intensity of fires and has a positive impact on the combustion behavior of heat-treated wood. As shown in Fig. 5, at the end of burning, the HRR curves of the heat-treated samples gradually decreased and tended to smooth out, which made the exothermic peaks simultaneously lower and wider. The wood charred early, suppressing HRR in the first stage. In the second stage, char-surface rupture occurred. Moisture in untreated samples can absorb heat and reduce the surface temperature, which limited the first exothermic peak and caused the longer TTI. Because the moisture content in heat-treated wood was lower and the cell walls were cracked, it was easier for moisture to be evaporated. Meanwhile, heat-treated wood produced volatile fatty acids that leaked to the wood surface, which acted as an effective fuel. From Table 3, heat-treated wood has a lower THR, which is consistent with the results of TGA. This suggests that heat-treating wood lowers its heat release rate. Due to the shorter TTI, it cannot be asserted that heat treatment was favorable with regard to the flame retardant performance of the wood.
Smoke production
In wood architecture, smoke production is the most important factor in wood safety research, even more so than heat release (Lee et al. 2011). Figure 6 shows the smoke production behavior of both heat-treated and untreated wood samples. The total smoke production curves are shown in Fig. 7.
Fig. 6. Smoke production rate (SPR) curves for untreated and heat-treated samples
Fig. 7. Total smoke production (TSP) curves for untreated and heat-treated samples
From Table 3 and Fig. 7, it was observed that heat treatment increased the average specific extinction area (av-SEA) and smoke production rate of wood. Compared to untreated wood, TSP values for 180 °C, 190 °C, and 210 °C-treated wood were significantly changed by 4.76, -5.5, and 43.3%, respectively. Based on these data, heat treatment generally had a negative effect on the smoke release properties of the treated wood.
Figure 6 shows the smoke release behavior of the samples. The smoke release process can be divided into 3 stages: (1) the non-flaming mode, (2) the flaming mode, and (3) the after-glowing mode. Figure 6 clearly shows that the smoke emission of the 210 °C-treated wood was larger than that of untreated wood in the first and second stages. Heat treatment reduced the equilibrium moisture content of the wood, thus increasing the surface heating rate and shortening the TTI (Table 3). However, heat treatment caused cracks in the pit membrane and the cell walls of the wood, which made it more porous (Figs. 2 and 3). Porous materials are more likely to carbonize, and the incomplete combustion during this period was due to the combustion of smoke (Senneca 2007). This result is of great significance regarding the safe use of heat-treated wood for indoor and outdoor applications and should be studied further.
CONCLUSIONS
- The thermal decomposition, combustion properties, and smoke emission behavior of heat-treated wood were investigated. The heat treatment changed the chemical composition of wood, especially hemicellulose.
- Tiny cracks in the cell walls and leakage of resin provided evidence that the degradation of the wood cell wall microstructure was a result of the heat treatment.
- Due to the degradation of hemicellulose, the intensity of hydroxyl and carbonyl peaks in the FTIR spectra of heat-treated wood decreased, indicating weaker hydrophilicity and better dimensional stability in the treated wood.
- Heat treatment showed positive effects on the fire safety of wood, weakening the intensity of its combustion and also reducing the ignition time of Larix spp. The smoke production of the heat-treated samples increased dramatically. The modification of the combustion behavior caused by the heat treatment should be further investigated.
ACKNOWLEDGMENTS
This work was supported by the National Natural Science Foundation of China (31270597).
REFERENCES CITED
Alén, R., Kotilainen, R., and Zaman, A. (2002). “Thermochemical behaviour of Norway spruce (Picea abies) at 180–225°C,” Wood Science and Technology 36(2), 163-171.
Almeida, A. L. F. S. D., Barreto, D. W., and Calado, V. J. (2008). “Thermal analysis of less common lignocellulose fibers,” Journal of Thermal Analysis and Calorimetry 91(2), 405-408.
Becidan, M., Skreiberg, Φ., and Hustad, J. E. (2007). “Products distribution and gas release in pyrolysis of thermally thick biomass residues samples,” Journal of Analytical and Applied Pyrolysis78(1), 207-213.
Candelier, K., Dumarcay, S., Petrissans, A., Desharnais, L., Gerardin, P., and Petrissans, M. (2013). “Comparison of chemical composition and decay durability of heat treated wood cured under different inert atmospheres: Nitrogen or vacuum,” Polymer Degradation and Stability 98(2), 677-681.
Colom, X., Carrillo, F., Nogués, F., and Garriga, P. (2003). “Structural analysis of photodegraded wood by means of FTIR spectroscopy,” Polymer Degradation and Stability 80(3), 543-549.
Das, S., Saha, A. K., Choudhury, P. K., Basak, R. K., Mitra, B. C., Todd, T., Lang, S., and Rowell, R. M. (2000). “Effect of steam pretreatment of jute fiber on dimensional stability of jute composite,” Journal of Applied Polymer Science 76(11), 1652-1661.
Duygu, K., and Sudeshna, S. (2012). “Comparison of the protection effectiveness of acrylic polyurethane coatings containing bark extracts on three heat-treated North American wood species: Surface degradation,” Applied Surface Science 258(13), 5283-5290.
Eseltine, D., Thanapal, S. S., Annamalai, K., and Ranjan, D. (2013). “Torrefaction of woody biomass (Juniper and Mesquite) using inert and non-inert gases,” Fuel 113, 379-388.
Evans, P. A. (1991). “Differentiating “hard” from “soft” woods using Fourier transform infrared and Fourier transform Raman spectroscopy,” Spectrochimica Acta Part A: Molecular Spectroscopy 47(9), 1441-1447.
Fang, Y. Q., Wang, Q. W., Guo, C. G., Song, Y. M., and Cooper, P. A. (2013). “Effect of zinc borate and wood flour on thermal degradation and fire retardancy of polyvinyl chloride (PVC) composites,” Journal of Analytical and Applied Pyrolysis 100, 230-236.
Fujii, T., Mochidzuki, K., Kobayashi, S., and Sakoda, A. (2011). “Quick and simple analysis of lignocellulose ingredients by thermogravimetric analysis,” Journal of the Japan Society of Material Cycles and Waste Management 22(5), 293-297.
Garcia, P., Wang, S., Shen, J., Rhodes, M., and Lee, W. J. (2008). “Effects of temperature on the formation of lignin-derived oligomers during the fast pyrolysis of Mallee woody biomass,” Energy Fuels 22, 2022-2032.
González-Peña, M. M., and Hale, M. D. C. (2009). “Colour in thermally-modified wood of beech, Norway spruce and Scots pine. I. Colour evolution and colour changes,” Holzforschung 63(4), 385-393.
Gua, X. L., Ma, X., Li, X. L., Liu, C. A., Cheng, K. H., and Li, Z. (2013). “Pyrolysis of poplar wood sawdust by TG-FTIR and Py–GC/MS,” Journal of Analytical and Applied Pyrolysis 102, 16-23.
Hakkou, M., Petrissans, M., Zoulalian, A., and Gerardin, P. (2005). “Investigation of wood wettability changes during heat treatment on the basis of chemical analysis,” Polymer Degradation and Stability89(1), 1-5.
Heigenmoser, A., Liebnerb, F., Windeisen, E., and Richter, K. (2013). “Investigation of thermally treated beech (Fagus sylvatica) and spruce (Picea abies) by means of multifunctional analytical pyrolysis-GC/MS,” Journal of Analytical and Applied Pyrolysis 100(1), 117-126.
Hosoya, T., Kawamoto, H., and Saka, S. (2006). “Thermal stabilization of levoglucosan in aromatic substances,” Carbohydrate Research 341(13), 2293-2297.
Hosoya, T., Kawamoto, H., and Saka, S. (2007). “Cellulose-hemicellulose and cellulose-lignin interactions in wood pyrolysis at gasification temperature,” Journal of Analytical and Applied Pyrolysis 80(1), 118-125.
Hosoya, T., Kawamoto, H., and Saka, S. (2008). “Pyrolysis gasification reactivities of primary tar and char fractions from cellulose and lignin as studied with a closed ampoule reactor,” Journal of Analytical and Applied Pyrolysis 83(1), 78-87.
Kamdem, D. P. A., Pizzi, A. B., and Jermannaud, A. C. (2002). “Durability of heat-treated wood,” Holz als Roh – und Werkstoff 60(1), 1-6.
Kasemsiri, P., Hiziroglu, S., and Rimdusit, S. (2012). “Characterization of heat treated Eastern redcedar (Juniperus virginiana L.),”Journal of Materials Processing Technology 212(6), 1324-1330.
Lee, B. H., Kim, H. S., Kim, S., Kim, H. J., Lee, B., Deng, Y. H., Feng, Q., and Luo, J. Y. (2011). “Evaluating the flammability of wood-based panels and gypsum particleboard using a cone calorimeter,” Construction and Building Materials 25(7), 3044-3050.
Li, Y. F., Liu, Z. B., Dong, X. Y., Fu, Y. L., and Liu, Y. X. (2013). “Comparison of decay resistance of wood and wood-polymer composite prepared by in-situ polymerization of monomers,” International Biodeterioration & Biodegradation 84, 401-406.
Nuopponen, M., Wikberg, H., Vuorinen, T., Maunu, S, L., Jämsä, S., and Viitaniemi, P. (2004). “Heat-treated softwood exposed to weathering,” Journal of Applied Polymer Science 91(4), 2128–2134.
Patwardhan, P. R., Satrio, J. A., Brown, R. C., and Shanks, B. H. (2010). “Influence of inorganic salts on the primary pyrolysis products of cellulose,” Bioresource Technology 101(12), 4646-4655.
Patwardhan, P. R., Brown, R. C., and Shanks, B. H. (2011). “Product distribution from the fast pyrolysis of hemicellulose,” ChemSusChem 4(5), 636-643.
Priadi, T., and Hiziroglu, S. (2013). “Characterization of heat treated wood species,” Materials & Design 49, 575-582.
Raveendran, K., Ganesh, A., and Khilar, K. C. (1996). “Pyrolysis characteristics of biomass and biomass components,” Fuel 75(8), 987-998.
Rowell, R. M., Ibach, E. R., McSweeny, J., and Nilsson, T. (2009). “Understanding decay resistance, dimensional stability and strength changes in heat treated and acetylated wood,” 4th European Conference on Wood Modification 4(1), 14-22.
Risto, A., Kotilainena, T. J. T., and Raimo, J. A. (2000). “FTIR monitoring of chemical changes in softwood during heating,” Journal of Wood Chemistry and Technology 20(3), 307-320.
Scudamore, M., Briggs, P., and Prager, F. (1991). “Cone calorimetry – A review of tests carried out on plastics for the association of plastic manufacturers in Europe,” Fire and Materials 15(2), 65-84.
Şen, A., Marques, A. V., Gominho, J., and Pereira, H. (2012). “Study of thermochemical treatments of cork in the 150-400 °C range using colour analysis and FTIR spectroscopy,” Industrial Crops and Products 38, 132-138.
Senneca, O. (2007). “Kinetics of pyrolysis, combustion and gasification of three biomass fuels,” Fuel Processing Technology 88(1), 87-97.
Shi, J. L., Kocaefe, D., and Zhang, J. (2007). “Mechanical behaviour of Québec wood species heat-treated using ThermoWood process,”Holz als Roh-und Werkstoff 65(4), 255-259.
Singh, T., Singh, A. P., Hussain, I., and Hall, P. (2013). “Chemical characterisation and durability assessment of torrefied radiata pine (Pinus radiata) wood chips,” International Biodeterioration & Biodegradation 85(SI), 347-353.
Tjeerdsma, B. F., Boonstra, M., Pizzi, A., Tekely, P., and Militz, H. (1998). “Characterisation of thermally modified wood: Molecular reasons for wood performance improvement,”Holz als Roh- und Werkstoff 569(3), 149-153.
Tjeerdsma, B. F., and Militz, H. (2005). “Chemical changes in hydrothermal treated wood: FTIR analysis of combined hydrothermal and dry heat-treated wood,”Holz als Roh- und Werkstoff 63(2), 102-111.
Varhegyi, G., Antal, M. J., Jakab, E., and Szabo, P. (1997). “Kinetic modeling of biomass pyrolysis,” Journal of Analytical and Applied Pyrolysis 42(1), 73-87.
Yang, H., Yan, R., Chen, H., Lee, D. H., and Zheng, C. (2007). “Characteristics of hemicellulose, cellulose and lignin pyrolysis,” Fuel 86(12-13), 1781-1788.
Yildiz, S., Gezer, E. D., and Yildiz, U. C. (2006). “Mechanical and chemical behavior of spruce wood modified by heat,” Building and Environment 41(12), 1762-1766.
Yildiz, S., Yildiz, U. C., and Tomak, E. D. (2011). “The effects of natural weathering on the properties of heat-treated alder wood,” BioResources 6(3), 2504-2521.
Zhang, X., Yang, W., and Blasiak, W. (2012). “Thermal decomposition mechanism of levoglucosan during cellulose pyrolysis,” Journal of Analytical and Applied Pyrolysis 96, 110-119.
Article submitted: April 14, 2014; Peer review completed: May 25, 2014; Revised version received and accepted: May 28, 2014; Published: June 3, 2014.