NC State
BioResources
  • Researchpp 2362-2373Stajić, M., Kukavica, B., Vukojević, J., Simonić, J., Veljović-Jovanović, S., and Duletić-Laušević, S. (2010). "Wheat straw conversion by enzymatic system of Ganoderma lucidum," BioRes. 5(4), 2362-2373.AbstractPDF
    The purpose of this study was to resolve the question of whether various nitrogen sources and concentrations affect characteristics of selected G. lucidum ligninolytic enzymes participating in wheat straw fermentation. This is the first study reporting the presence of versatile peroxidase activity in crude extract of G. lucidum culture, as well as isoforms profile of Mn-oxidizing peroxidases. NH4NO3 was the optimum nitrogen source for laccase and Mn-dependent peroxidase activity, while peptone was the optimum one for versatile peroxidase activity. with laccase activity were obtained by native PAGE and IEF separations from medium enriched with inorganic nitrogen source, and only two bands from medium containing organic source. Medium composition was not shown to affect isoenzyme patterns of Mn-oxidizing peroxidases. Four isoforms of Mn-dependent peroxidase and three of versatile peroxidase were obtained on native PAGE. By IEF separation, five isoforms of Mn-dependent peroxidase and only two of versatile peroxidase were observed. The results demonstrated that G. lucidum has potential for mineralization and transformation of various agricultural residues and should take more significant participation in large-scale biotechnological processes.
  • Researchpp 2374-2390Pirraglia, A., Gonzalez, R., and Saloni, D. (2010). "Techno-economical analysis of wood pellets production for U.S. manufacturers," BioRes. 5(4), 2374-2390.AbstractPDF
    Many companies in the U.S. are entering the wood pellets market due to the increasing importance of woody biomass utilization for energy purposes. Despite a 200% increase in U.S. production, it is difficult to obtain reliable information from the research community relative to the production costs, requirements, and market trends for wood pellets. Based on comprehensive investigations, a techno-economical model for the determination of production costs for U.S. manufacturers (internal market, with sell strategy based on bagged product) was developed, considering the most important technical and financial factors that affect pellet production. Outcomes from a case-study show that pellet production is profitable for U.S. manufacturers and distributors/retailers, with more revenue margin for retailers. Sensitivity analyses were performed, showing that a pellet plant is especially sensitive to changes to the cost of biomass and labor. In addition, changes in energy and CAPEX also affect the NPV and IRR of the project, but not as significantly as biomass and labor costs. Additional findings indicate that increasing the plant size especially increases CAPEX, with labor being the least increased cost factor; in addition, production factors have to be closely monitored for small-scale producers, due to increases in operational costs.
  • Researchpp 2391-2403Mahdavi, S., Kermanian, H., and Varshoei, A. (2010). "Comparison of mechanical properties of date palm fiber-polyethyelene composite," BioRes. 5(4), 2391-2403AbstractPDF
    Date Palm Fiber (DPF) is one of the most available natural fibers in the Middle East, especially in Iran and the Persian Gulf region. This research provides a new insight into DPF, with consideration of morphological, chemical characteristics, and bulk density, as well as morphological and mechanical properties of DPF/HDPE wood plastic composite. There are three parts of date palm that are used for producing fiber, the trunk, rachis, and petiole. Results indicated that there is significant difference between trunk and petiole on fiber length but rachis has no significant differences relative to the other parts. The aspect ratios have significant differences among of three parts, with the highest and lowest values measured for the petiole and trunk, respectively. The chemical composition of various parts of the date palm tree differed significantly; with the highest amounts of cellulose and lignin content belong to rachis. Bulk density was measured for three parts of date palm, and the lowest amount was 0.082 g/cm3. The highest strengths were achieved in composites with 30 and 40% fiber content, depended on which original parts of the tree were used.
  • Researchpp 2404-2416Kurian, J. K., Minu, A. K., Banerji, A., and Kishore, V. V. N. (2010). "Bioconversion of hemicellulose hydrolysate of sweet sorghum bagasse to ethanol by using Pichia stipitis NCIM 3497 and Debaryomyces hansenii sp.," BioRes. 5(4), 2404-2416.AbstractPDF
    Production of ethanol from concentrated D-xylose solutions and hemicellulose hydrolysate of sweet sorghum bagasse was achieved by using Pichia stipitis NCIM 3497 and an isolated yeast Debaryomyces hansenii sp. These yeasts werecapable of producing ethanol from solutions containing 800 g/L D-xylose, and the optimum sugar concentration was found to be 150 g/L at pH 4, 30oC, with a production time of 72 hours. These yeasts were capable of utilizing multiple sugars. Hemicellulose hydrolysates of sweet sorghum bagasse were obtained by dilute acid hydrolysis and autohydrolysis including steam explosion treatment. The hydrolysate was treated by an over-liming process for detoxification and pH adjustment. Ethanol yield from hemicellulose hydrolysate was found to be higher than that of synthetic medium containing D-xylose. These yeasts can be used in production of ethanol from concentrated hemicellulose hydrolysates containing high pentose sugars obtained while treating lignocellulosic biomass at high substrate concentrations.
  • Researchpp 2417-2430Ogunsile, B. O., and Quintana, G. C. (2010). "Modeling of soda-ethanol pulps from Carpolobia lutea, BioRes. 5(4), 2417-2430.AbstractPDF
    The chemical properties and soda-ethanol pulping of Carpolobia lutea was investigated as an alternative raw material for pulp and paper production. The influence of temperature, time, and concentration of pulping liquor on the pulp yields and residual lignin contents was evaluated using a central composite design. The maximum variation in the minimum residual lignin content was caused by changes in time, while temperature and time were responsible for the variation in the highest pulp yield. A maximum pulp yield of 48.53% was obtained at low values of the process variables. The selectivity of lignin dissolution was independent of the working conditions but allowed quantitative estimations to be established between the yield and residual lignin content within the range studied. Combined effects of temperature and time revealed that pulping at high temperature for a short time may be more advantageous, especially when high rate of delignification and substantial savings in time is required.
  • Researchpp 2431-2446Zhong, L., Fu, S., Li, F., and Zhan, H. (2010). "Chlorine dioxide treatment of sisal fibre: Surface lignin and its influences on fibre surface characteristics and interfacial behaviour of sisal fibre/phenolic resin composites," BioRes. 5(4), 2431-2446.AbstractPDF
    This paper describes an investigation of the influences of chlorine dioxide treatment on fibre surface lignin. The fibre surface characteristics and the interfacial behaviour of the sisal fibre/phenolic resin composites were also studied by SEM, AFM, and XPS. The results show that the surface of the untreated fibre contains a large amount of lignin with granular structure and non-granular structure. The surface lignin concentration is up to 51% for the untreated fibre, and then it decreases to 24% and 20% for fibres treated with 1.5 % and 2.0% chlorine dioxide, respectively. The removal of lignin from the fibre surface can enhance the interfacial strength of the composites, giving rise to increases by 36% and 28% in tensile strength and internal bonding strength. These results indicate that the surface properties of single sisal fibres can be tailored to improve the fibre/resin interface. Chlorine dioxide treatment has potential for surface modification of sisal fibre in engineering the interfacial behaviour of composites.
  • Researchpp 2447-2456Hu, J., Xu, G., Liu, J., Lei, T., and Shen, S. (2010). "Finite element modeling simulation in the straw pellet cold compressing molding process," BioRes. 5(4), 2447-2456.AbstractPDF
    According to the character of straw pellet fuel cold molding technology, the compressing process was modeled by Finite Element Modeling (FEM) structure analysis tools. This indicated the variation laws between the stress and the strain, and the influence of the structure parameters of the die on the stress and the strain. It’s concluded from the work that when the length-to-diameter ratio of the die was 5.2 and the conicity of the die was 45o, the compress molding showed better degree of bonding and finish. This provided theoretical evidence for the study of the molding mechanism of the straw pellet and the selection of the structure parameters of the die.
  • Researchpp 2457-2469Hoseinpour, H., Karimi, K., Zilouei, H., and Taherzadeh, M. J. (2010). "Simultaneous pretreatment of lignocellulose and hydrolysis of starch in mixtures to sugars," BioRes. 5(4), 2457-2469.AbstractPDF
    Mixtures of starch and lignocelluloses are available in many industrial, agricultural, and municipal wastes and residuals. In this work, dilute sulfuric acid was used for simultaneous pretreatment of lignocellulose and hydrolysis of starch, to obtain a maximum amount of fermentable sugar after enzymatic hydrolysis with cellulase and β-glucosidase. The acid treatment was carried out at 70-150°C with 0-1% (v/v) acid concentration and 5-15% (w/v) solids concentration for 0-40 minutes. Under the optimum conditions, obtained at 130°C, 1% acid, and 7.5% solids loading for 30 min, the starch was almost completely converted to glucose. However, the acid treatment was not successful for efficient hydrolysis of pure cellulose. A mixture of pine softwood and potato as representatives of lignocellulosic and starch components, respectively, were treated at the optimum conditions for acid hydrolysis of starch. The dilute-acid treatment resulted in 1.2, 60.5, and 23.6% hydrolysis of glucan, xylan, and mannan of pine wood and 67% of potato starch to fermentable sugars. After the acid treatment, the solid residue of the mixture was subjected to enzymatic hydrolysis. The enzymatic hydrolysis under the optimum conditions resulted in conversion of 76% of the glucan in the treated softwood. Therefore, using acid treatment of the mixture is a promising process for pretreatment of wood in addition to the hydrolysis of starch.
  • Researchpp 2470-2477Rao, M., Varma, A. J., and Deshmukh, S. S. (2010). "Production of single cell protein, essential amino acids, and xylanase by Penicillium janthinellum," BioRes. 5(4), 2470-2477.AbstractPDF
    Microbial biomass having 46% crude protein content and enriched with essential amino acids as well as extracellular xylanase activity (100-150 IU/ml) was produced by an efficient fungal strain, Penicillium janthinellum (NCIM St-F-3b). Optimization studies for maximum xylanase and biomass production showed that the fungus required a simple medium containing bagasse hemicellulose as carbon source and ammonium sulphate as the nitrogen source. Therefore bagasse, which is a waste product of the sugar industry, can be efficiently used in microbioal biomass protein preparation for animal feed.
  • Researchpp 2478-2501Esmeraldo, M. A., Barreto, A. C. H., Freitas, J. E. B., Fechine, P. B. A., Sombra, A. S. B., Corradini, E., Mele, G., Maffezzoli, A., and Mazzetto, S. E. (2010). "Dwarf-green coconut fibers: A versatile natural renewable raw bioresource. Treatment, morphology, and physicochemical properties," BioRes. 5(4), 2478-2501.AbstractPDF
    Dwarf-green coconut fibers were modified by alkali treatment and characterized by scanning electron microscopy (SEM), X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FT-IR), as well as thermogravimetric (TGA), mechanical, and dielectric analyses. Changes in composition, structure, and morphology of the coconut fibers were observed after sodium hydroxide treatments due to the removal of lignin, hemicellulose, and other impurities. The XRD data were in agreement with the morphological analysis, where the crystallinity fraction increased with the concentration of alkali solution and fell off above 10%. The infrared spectrometry showed the partial dissolution of hemicellulose, lignin, and pectin, which was clearly identified by the band at 1736 cm-1. Thermogravimetric analysis showed a double degradation process for the untreated dwarf-green coconut fibers, while a single one was observed after the pretreatment. The tensile properties showed an increased elongation at break, modulus, and strength, and the dielectric results showed a decrease of all parameters (permittivity, dielectric loss, and conductivity), reflecting the reduced dipole and ion mobility associated with the loss of amorphous components.

@BioResJournal

55 years ago

Read More