Abstract
Download PDF
Full Article
Sugar Palm Fibre and its Composites: A Review of Recent Developments
Isma’ila Mukhtar,a,d,* Zulkiflle Leman,a,c Mohamad Ridzwan Ishak,b,c and Edi Syams Zainudin a,c
The use of natural fibres as reinforcement in composite materials has increased over the years due to the rapid demand for renewable, cost-effective, and eco-friendly materials in many applications. The most common and adopted natural fibres used as reinforcements are flax, kenaf, hemp, jute, coir, sisal, and abaca. However, sugar palm fibre (SPF) as one of the natural fibres is gaining acceptance as a reinforcement in composites, though it has been known for decades in the rural communities for its multipurpose traditional uses. Sugar palm fibre (SPF) is extracted from sugar palm tree typically from its four morphological parts, namely, trunk, bunch, frond, and the surface of the trunk, which is known as Ijuk. In this paper, sugar palm tree, its fibre and composites, and biopolymers derived from its starch are discussed. Major challenges and the way forward for the use of sugar palm fibre and its composites are highlighted. This review also opens areas for further research on sugar palm fibre and its composites for academia and industries.
Keywords: Sugar palm fibre; Natural fibre composites; Biopolymer; Properties; Biodegradability
Contact information: a: Department of Mechanical and Manufacturing Engineering, Faculty of Engineering, Universiti Putra Malaysia, 43400 UPM Serdang, Selangor Darul Ehsan, Malaysia; b: Department of Aerospace Engineering, Faculty of Engineering, Universiti Putra Malaysia, 43400 UPM Serdang, Selangor Darul Ehsan, Malaysia; c: Laboratory of Biocomposites Technology, Institute of Tropical Forestry and Forest Product (INTROP) Universiti Putra Malaysia, 43400 UPM Serdang, Selangor Darul Ehsan, Malaysia; d: Department of Mechanical Engineering, Faculty of Engineering, Kano University of Science and Technology Wudil, PMB 3244 Kano State, Nigeria;
* Corresponding author: ismailmuk@gmail.com
Introduction
The increase in stringent regulations on carbon emissions, environmental concerns such as climate change, and the disposal of components at the end of their useful life has stimulated the use of environmentally friendly materials. In recent years, the furniture, automobile, packaging, aerospace, building, and construction industries have searched for new materials to replace the conventional glass fibre and other synthetic fibre composites. The most promising and adopted materials are natural fibre composites. Natural fibre composites are developed by a combination of two or more distinct materials to obtain a material with required properties and performance that is not obtainable from any distinct material (Bledzki and Gassan 1999). In a natural fibre composite, one material will be a matrix, while the other material will be a reinforcement produced from plants or animals, including bast, leaf, seed, fruit, stalk, grass, and wood. The matrix can either be thermoplastic, thermoset, or biopolymer. The most commonly used thermoplastic materials for natural fibre composites are polypropylene, polyethene, and poly (vinyl chloride) PVC; in thermoset plastics, they are epoxy, polyester, and phenolic (Malkapuramet al. 2008).
Natural fibre composites offer numerous advantages compared with glass fibre composites, including their light weight, biodegradability, ease of machinability, lack of toxicity, low cost, non-abrasive nature, and availability (Garkhail et al. 2000; Malkapuram et al. 2008). There are many natural fibre composites that are acceptable and well established through research. Wambuaet al. (2003) investigated the mechanical properties of sisal, hemp, coir, kenaf, and jute reinforced polypropylene, and another study by Rao and Rao (2007) investigated the physical and mechanical properties of vakka, date, and bamboo. More recently, sugar palm fibre has been explored as a potential reinforcement in a polymeric matrix (Leman et al. 2005; Ishak et al. 2009; Sapuan et al. 2010; Ishak et al. 2012). With the evolution of these new natural fibre composites, certain precautions need to be taken with regard to the area of application. These composites should be critically evaluated and characterized for proper utilisation in a wider range of applications.
This review provides an overview of the sugar palm tree and its fibre and composites. The article highlights the characterization of sugar palm fibre, its chemical composition, treatment, and product development, as well as the engineering properties of sugar palm fibre reinforced thermoset, thermoplastic, and biopolymer composites. It will also open areas of further research of sugar palm fibre and its composites.
Natural fibres
Lignocellulose fibres or natural fibres are natural substances produced by plants (cellulose or lignocellulose), animals (protein), and minerals.
Fig. 1. Classification of natural fibres (redrawn from Jawaid and Khalil (2011) and Sanyang et al. (2016b))
Usually, these fibres are spun into filament, thread, or rope, and they can be matted, knitted, or woven as products or as a material for reinforcement. Natural fibres are found in many sources; the subdivision is based on their origins, coming from either plant, animal, or mineral as shown in Fig. 1 (Holbery and Houston 2006; Jawaid and Khalil 2011; Sanyang et al. 2016b). The bulk of natural fibres originate from plants including abaca, coir, cotton, flax, hemp, jute, ramie, and sisal; these are the most established natural fibres (Bledzki and Gassan 1999). The word “fibre” in this context refers to a structure that consist of several cells. These cells are organised and bonded together through mechanical interactions, hydrogen bonds, and van der Waals forces between domains of microfibrils of cellulose, hemicellulose, and lignin. (Pérez et al. 2002). The natural fibres are mostly in the form of agricultural waste that is unutilized, except for burning as fuel, thereby contributing to environmental problems. An assessment of biofuel use and agricultural waste field burning by Yevich and Logan (2003) showed that agricultural waste provides about 33% of the biofuel used globally. This agricultural waste is produced in billions of tonnes, which are in abundant and at low cost. Most of this waste could be used as fibres and fillers in polymeric composites. Because there are many sources of natural fibres, their utilisation in various industrial applications is undoubtedly supported by their bulk availability in many countries.
Based on the classification of natural fibres, sugar palm fibre being relatively new when compared with other natural fibres, it can find its position in more than one places. The reason is that the fibre from the sugar palm tree can come from either bunch, frond or trunk (Sahari et al.2011, 2012; Ishak et al. 2013;). Therefore, sugar palm fibre can appear both under fruit, bast and leaf in the classification of natural fibres as shown in Fig. 1.
Natural fibres offer some advantages over synthetic fibres such as glass, as depicted in Table 1 (Garkhail et al. 2000; Joshi et al. 2004; Malkapuram et al. 2008). The benefits of natural fibres often outweigh the disadvantages. Natural fibres offer weight reduction and cost savings, because of its low density and availability. In addition, it degrades easily and it offers ease of machinability with minimum tool wear. Though it has low thermal stability, poor compatibility, and poor resistance to environment. But if these unique technical problems posed by the natural fibres can be resolved, natural fibres can replace glass fibre and other synthetic fibres even in outdoor applications.
Table 1. Advantages and Disadvantages of Natural Fibres (Garkhail et al. 2000; Joshi et al. 2004; Malkapuram et al. 2008)
A comparison between natural and glass fibres is shown in Fig. 2 (Wambua et al. 2003; Sanyanget al. 2016b). While natural fibres degrade easily, synthetic fibres are difficult to naturally degrade; carbon dioxide emission and the requirement for non-renewable energy for the production of glass fibre is much higher than natural fibres (Joshi et al. 2004). These are some of the reasons why natural fibres are increasingly replacing synthetic fibres in many applications.
Fig. 2. Comparison between natural fibre and glass fibre (Wambua et al. 2003; Sanyang et al. 2016b)
History of sugar palm tree and its fibre
The sugar palm tree (Arenga pinnata) is a member of the Palmae family. This plant is normally found in hot, humid parts of the Asian tropics, and it has the widest range of uses, which makes it a multipurpose palm species. Many of the more than 3000 tropical and subtropical palm species can be classified as multipurpose (Mogea et al. 1991). Sugar palm trees are found in tropical South and Southeast Asia, including Indonesia, Malaysia, India, Philippines, Papua New Guinea, North Australia, Thailand, Burma, Vietnam, etc. (Dransfield et al. 2005; Sahari et al. 2012). In Malaysia, sugar palm trees are found along the rivers in rural areas; its plantation growth covers approximately 892 hectares (Sahari et al. 2012b). In Indonesia, there are about 150 vernacular names for this multipurpose palm, including but not limited to “kelapa”, “merah”, “semut”, “gomuti”, “kaong”, and “aren” (Heyne 1950); in Malaysia it is called “enau” or “kabung” (Ishaket al. 2013).
The sugar palm tree grows close to human settlement and sometimes grows in the secondary forest to the border of primary rainforest from the lowland up to the altitude of about 1400 m (Mogea et al. 1991). Its trunk is solitary, straight, and usually 15 to 20 m in height and up to 65 cm in diameter (Sanyang et al. 2016b). It has large leaves up to 6 m long. The trunk is covered with black fibrous hair, commonly known as Ijuk or Injuk. The fibres found along its height have different chemical compositions and hence vary in properties (Ishak et al. 2012). The sugar palm tree starts to flower between the age of 10 to 12 years, but early flowering can occur as early as 5 to 6 years. The tree dies after a lifetime of 12 to 20 years depending on the harvest environment (Mogea et al. 1991; Suwartapradja 2003). Figure 3 shows pictures of sugar palm trees (Wanderer 2010).
Fig. 3. Sugar palm tree and its trunk loaded with fibre (Wanderer 2010)
Table 2. Traditional and Modern Uses of Sugar Palm Trees (Mogea et al. 1991; Sahari et al.2012b)
Uses of Sugar Palm Tree
Sugar palm is a great source of food, beverages, biofibres, biopolymers, and biocomposites (Sahari et al. 2012b). It is a popular plant because of its year-round food production, especially in the dry season when other food sources are scarce in rural areas. Virtually all of its parts can be used. Traditionally, this palm is used principally for sugar, and the tree sap can be processed into gula aren/gula kawong/gula beureum (Suwartapradja 2003). It is used as a drink or as a raw material for nectar sweetener (Mogea et al. 1991) or is fermented to produce biofuel, namely bioethanol (Ishak et al. 2012), yielding up to 20,160 litres of bioethanol per hectare per year (Sahari et al. 2012b). However, its seed and the tip of its stem are edible vegetables. The shaggy material at the base of the leaves makes an excellent rope, as it is strong and resists decay. Table 2 summarises the uses of sugar palm trees.
Sugar Palm Starch
The starch from the sugar palm trunk can be utilised as a biopolymer, which can be used with natural fibre to produce a “biocomposite” or “green composite”. The starch is abundant inside the trunk of the sugar palm tree, which when modified by either plasticization or blending can be used as a biopolymer (Imre and Pukánszky 2013). The use of the starch as a biopolymer will greatly reduce dependency on petroleum-based polymers. Sahari et al. (2012a, 2013b) explored the potential of using sugar palm starch as a biomatrix by plasticizing the starch with glycerol. The effect of the plasticiser on the physical, thermal, and mechanical properties was studied. Sahari et al. (2013a) produced a biocomposite (i.e., sugar palm fibre as reinforcement and biopolymer from starch of sugar palm tree as matrix) with increased tensile strength and modulus and flexural strength and modulus. Impact strength increased with fibre loading, but the elongation at break decreased. In the same composite, the water absorption decreased with increased fibre loading, which was similar to moisture content. Sugar palm fibre has better water resistance than biopolymers from sugar palm starch, but this can be overcome with further research by modification of the biomatrix. The starch from sugar palm tree can be plasticized and formed into a film for food packaging (Sanyang et al. 2015, 2016a).
Fig. 4. Sugar palm tree, its fibre, and SEM image of single fibre (Bachtiar et al. 2008; Ishak et al. 2013)
Sugar Palm Fibre
Another important part of this tree is its fibre. Figure 4 shows a sugar palm plant, a fibre bunch, and an SEM image of the fibre (Bachtiar et al. 2008; Ishak et al. 2013). The full length of its trunk is completely covered with black fibre locally known as gomuti fibre or Ijuk. The traditional or early applications of this fibre includes paint brushes, septic tank base filters, door mats, carpet, ropes, chair/sofa cushions, brooms, road construction, roofing materials, and shelters for fish breeding (Mogea et al. 1991; Suwartapradja 2003; Bachtiar et al. 2008). The modern application of sugar palm fibre includes fabrication of a small boat (Misri et al. 2010); a hybridised glass fibre and sugar palm fibre reinforced unsaturated polyester composite was used for the small boat manufacturing using the hand lay-up technique. Razak and Ferdiansyah (2005) used SPF as reinforcement in concrete, and the addition of fibre increased the toughness characteristics of the concrete compared with plain concrete. With research and development, the application will go beyond boat manufacturing and concrete reinforcement as other areas of applications are identified.
The quality of sugar palm fibre makes it an export product. From 1976 to 1985, approximately 2400 tonnes of SPF, at a value of about 1.5 million USD, were exported annually to West Germany only from Java, Indonesia (Mogea et al. 1991). Unlike other natural fibre, sugar palm fibre does not require chemical or mechanical extraction, as this fibre is naturally wrapped around the trunk.
Characterization of sugar palm fibre (SPF)
Utilising SPF as a reinforcement in polymer matrix is a relatively new application. To recognise the strengths and weaknesses of natural fibre composites, it is necessary to comprehend the physical, mechanical, and thermal properties of the fibres. Research on SPF and its composites started around the year 2005, but these properties are not well established. A few reports on SPF physical, chemical, mechanical, and thermal properties will be reviewed critically (Bachtiar et al.2010; Ishak et al. 2012; Sahari et al. 2012; Ticoalu et al. 2014).
Fig. 5. Structure of natural fibre (redrawn from Kalia et al. (2009) and Rong et al. (2001))
Structure and Chemical Composition of SPF
The chemical composition, chemical structure, and cell structure arrangement of natural fibre are very important. These parameters are responsible for the performance and durability of the natural fibre composites in their various applications. The structural arrangement of plant fibre is shown in Fig. 5. The natural fibre has a complex layered structure, where the outermost primary wall encloses the secondary wall. The secondary wall consists of three layers namely, S1, S2, and S3. The middle layer S2 is the thickest (approximately 80% of the total thickness of the fibre) and is responsible for the mechanical properties of the fibre (Rong et al. 2001). The layers consist of helically wound cellulose microfibrils, which are bound together by an amorphous lignin serving as a binder (Kalia et al. 2009); while hemicellulose acts to strengthen the cell wall by interaction with cellulose and lignin via non-covalent forces (Scheller and Ulvskov 2010). Evidently, there is covalent bonding between lignin and hemicellulose (Lawoko et al. 2005). Cellulose and lignin are most important two fibre components, as hemicellulose burnt out at an early stage of thermal analysis. This has motivated Birnin-Yauri et al. (2016b) to conduct a study by combining a cellulose-rich fibre and lignin-rich fibre to form a hybrid composite. The results showed synergistically improved properties. The crystal structure, microfibril angle, size of lumen, size of the crystalline region, porosity, and void have a strong influence on properties of natural fibres and its composite (Baley 2002; Kalia et al. 2011).
The chemical composition of natural fibres generally reveals the content of cellulose, hemicellulose, lignin, pectin, ash, and other naturally occurring constituents (Kalia et al. 2009; Rong et al. 2001). Hemicellulose, cellulose, and lignin are the three main components of lignocellulose material, comprising 10 to 25 wt.%, 31 to 70 wt.%, and 7 to 26 wt.%, respectively (McKendry 2002; Li et al. 2007; Yang et al. 2007). These constituents of plant fibre contain the stored chemical energy, which varies from plant to plant (McKendry 2002). Looking at the proportion of the composition, the cellulose is the main constituent of natural fibre, and it provides mechanical strength (Reddy and Yang 2005). Unlike cellulose, hemicellulose does not give significant contributions to the strength of the natural fibre, but it binds microfibrils of the fibre (Reddy and Yang 2005). In addition, cellulose is a highly crystalline structure with about 80% crystalline region (Ho et al. 2012). Lignin is an amorphous complex of polymers of phenylpropane units, and it functions as an encrusting agent or simply as a matrix (Han and Rowell 1997).
The chemical compositions of sugar palm fibre were determined in previous research (Sahari et al. 2012; Ishak 2013). Sahari et al. (2012) investigated the chemical composition of sugar palm fibre, as shown in Table 3. The fibre can be obtained from four different morphological parts, i.e., frond, bunch, trunk, and Ijuk (the surface of the trunk). The compositional percentage of cellulose, holocellulose, and lignin are all within the range of natural fibres stated by McKendry (2002). Frond has the highest percentage of cellulose, followed in decreasing order by bunch, Ijuk, and trunk. Ijuk fibre contains almost 90% of the total fibres from the sugar palm tree.
Table 3. Chemical Composition of Sugar Palm Fibre Obtained from Different Morphological Parts of the Tree
Source: Sahari et al. 2012
Ishak et al. (2013) investigated the chemical composition of the Ijuk fibre obtained from different heights of the trunk, i.e., 1, 3, 5, 7, 9, 11, 13, and 15 m, as shown in Table 4. The cellulose, hemicellulose, and lignin contents increased with the increase of sugar palm tree height and were directly proportional to tensile strength, modulus, and elongation values. Cellulose and hemicellulose content decreased at the upper part of the tree, which was attributed to the juvenile stage of the fibre. It was concluded that biological degradation took place at the bottom part of the tree where brown or broken fronds were seen. The use of fibre around a dead palm frond as reinforcement in a composite should be avoided because the fibres in that location are biologically degraded, leading to broken polymeric chains and inferior properties (Ishak et al.2012). Fibres between 5 to 11 m showed optimum properties, based on the chemical composition of the fibre. The fibres within this range are free from sand and mature. Chalid et al. (2015) studied the chemical composition of Ijuk fibre and found 28.32 wt.% lignin, 51.44 wt.% cellulose, and 23.88 wt.% hemicellulose, which was in agreement with results obtained by Sahari et al.(2012) and Ishak et al. (2013).
Table 4. Chemical Composition of Sugar Palm Fibre Obtained from Different Heights of the Tree
Source: Ishak et al. 2013
Table 5. Chemical Composition of SPF in Comparison with Other Natural Fibres
Source: (Baley 2002; Li et al. 2007; Ayrilmis et al. 2011; Kabir et al. 2012; Sahari et al. 2012; Ishak et al. 2013; Omrani et al. 2015; Birnin-Yauri et al. 2016a)
The chemical constituents of natural fibres vary, and these variations can be observed even in fibres from the same plant. Several factors are responsible for these variations, including soil quality, weather condition, geographical location, morphological part of the plant, maturity/age of the plant, extraction methods, and test equipment used (Koronis et al. 2013). Tables 3 and 4 show variations in the chemical constituents of SPF. In comparison, there are variations reported by Ishak et al. (2013) and Sahari et al. (2012). The former analysed the chemical composition obtained from a different height of trunk, while the latter considered fibres from different morphological parts, i.e. frond, bunch, trunk, and Ijuk. The chemical composition of sugar palm fibre in comparison with other established natural fibres is compiled in Table 5 based on data from various authors (Baley 2002; Li et al. 2007; Ayrilmis et al. 2011; Kabir et al. 2012; Sahari et al. 2012; Ishak et al. 2013; Omrani et al. 2015). The properties and percentage of each chemical constituent of natural fibre contribute significantly to the overall engineering properties of the natural fibre. Compared with other natural fibres, the cellulose content of SPF, which mainly provides strength, is higher than that of coir and kenaf, but it is within the range of abaca, flax, and jute. This is a strong justification that sugar palm fibre is a potential reinforcement in natural fibre composites. Sugar palm fibre is qualified because its cellulose, hemicellulose, and lignin contents are well within the range of established natural fibres.
Table 6. Comparative Physical Properties of SPF and Other Natural Fibres
Source: (Mwaikambo and Ansell 2006; Dhakal et al. 2007; Li et al. 2007; Kalia et al. 2009; Defoirdt et al. 2010; Ku et al. 2011; Martin et al. 2013; Ticoalu et al. 2014)
Physical and Mechanical Properties
The sugar palm fibre known as Ijuk is black/brown in colour, and its various physical and mechanical properties have been reported in the literature. The density and diameter of SPF were determined by several authors using different methods, but the results come with variations from one author to another. This can be attributed to the known quality variations of natural fibres and equipment/procedure employed for the measurement. Razak and Ferdiansyah (2005) reported a diameter range of 300 to 500 µm. Suriani et al. (2007) reported a range of 94 to 370 µm, which is close to the findings of Bachtiar et al. (2010), who got a range of 99 to 311 µm using weighing in conjunction with formula method. In another study, Sahari et al. (2012) reported a value of 212 µm for the diameter of Ijuk fibre. Ticoalu et al. (2014) found the diameter to be 81 to 313 µm, and Chalid and Prabowo (2015) reported 376 µm. Based on the reported work from literature, Ijukfibre has a diameter range of 81 to 500 µm, which is comparable with coir and sisal. The physical properties of SPF and well-established natural fibres such as jute, ramie, sisal, coir, and kenaf were compiled in Table 6 (Paul et al. 1997; Baley 2002; Mwaikambo and Ansell 2006; Bogoeva‐Gaceva et al. 2007; Dhakal et al. 2007; Li et al., 2007; Munawar et al. 2007; Kalia et al. 2009; Defoirdt et al. 2010; Ku et al. 2011; Martin et al. 2013; Ticoalu et al. 2014). Sugar palm fibre has values similar to other natural fibres. The density of SPF is comparable with that of hemp, flax, and kenaf but higher than coir. The moisture content of SPF is between 5.36 to 8.7%, as reported by Ishak et al. (2012), which is much lower than that of jute, sisal, coir, and bagasse, which have 12, 11, 10, and 8.8 %, respectively (Rowell 2008).
The tensile properties of natural fibre, namely, tensile strength, modulus, and elongation, are determined through a single fibre tensile test. In single fibre testing, the test length should be critically chosen to avoid too many flaws within the gauge length; the strength of single fibre decreases with increased gauge length, which was verified for coir, bamboo, and jute fibres by Defoirdt et al. (2010). For better prediction of the performance of the natural fibres, the data in Table 6 were used to determine the specific tensile strength and specific tensile modulus of various natural fibres, which are shown in Fig. 6.
Fig. 6. Average specific tensile strength and modulus of natural fibres
The specific tensile strength and specific stiffness are important indicators for mechanical performance. These values were depicted in Fig. 6, and it can be observed that sugar palm fibre can be a true reinforcing material in natural fibre composite because of its competitive average specific strength and specific modulus values compared with other natural fibres like coir and kenaf. Natural fibres with high specific strength and modulus have a special advantage in an application where weight is a critical factor, such as automotive applications. Flax, ramie, and hemp have superior mechanical performance in comparison with other natural fibres.
Thermal Properties
The most frequently used thermal analysis technique is thermogravimetric analysis (TGA). It is widely used to characterise materials by measuring their change in mass as a function of temperature. A natural fibre is thermally stable over a temperature range where there is no significant change in fibre mass. This range can be seen in the thermograph of the change in weight versus temperature. Usually, this temperature range is used to determine the natural fibre composite processing temperature. A thermal analysis of sugar palm fibre by Ishak et al. (2012) showed that SPF decomposed in phases in the following order: evaporation of moisture (45 °C to approximately 123 °C), followed by the decomposition of hemicellulose (210 to 300 °C), cellulose (300 to 400 °C), lignin (160 to 900 °C), and ash (1,723 °C). The decomposition of lignin starts much earlier than hemicellulose and cellulose and covers a wide temperature range. It occurs at a lower rate, which makes it difficult to decompose (Yang et al. 2007). In another thermal analysis by Ticoalu et al. (2014), the first loss in weight was ~ 4.1% at 48.1 °C for moisture evaporation, while hemicellulose starts to decompose at a temperature of 248 °C with a weight loss of ~ 17.5%. The major weight loss of ~ 44.1% was during the decomposition of cellulose at 324.8 °C. Based on this analysis, sugar palm fibre had an onset thermal degradation of 222.8 °C, which means that the processing temperature of sugar palm composite should be below this temperature to avoid degradation of the fibre during processing.
Limitations of sugar palm fibre
Sugar palm fibre and other natural fibres have many positive reasons for being used as reinforcing fillers in polymers, at the same time there are also several limitations associated with them. The hydrophilic nature of natural fibres is the major limitation compared to conventional reinforcing fibres like glass, carbon, and aramid. The other limitations are depicted in Fig. 7. When these drawbacks are resolved, natural fibres will be the leading reinforcement fillers in the field of composite materials because of their competitive advantages.
Fig. 7. Bottlenecks of natural fibres as reinforcement in polymer (Faruk et al. 2014; Senwitz et al.2016)
The most worrisome drawback of natural fibre composite is lack of interfacial adhesion between the filler and the polymeric matrix. In a given composite, the matrix has a role of transferring the load to the reinforced fibre through shear stresses at the interface of the matrix and fibre. Load-bearing capacity of a composite largely depends on the bonding between the natural fibre and the matrix. Having poor adhesion at the interface will weaken the fibre and consequently yield poor mechanical properties that will render the material incapacitated in many applications. A potential solution to this problem is to treat the fibre or modify the matrix for better adhesion (Bachtiar et al. 2008; Leman et al. 2008; Ishak et al. 2009; Leman et al. 2010; Sapuan et al. 2010; Bachtiar et al. 2011; Ishak et al. 2011a; Ticoalu et al. 2014). Poor resistance to water absorption is another drawback of natural fibres, which limits their usage to indoor applications. This phenomenon is a result of the hydroxyl group of the natural fibre, which tends to react with water molecules by hydrogen bonding, making it degrade and swell easily when exposed to the changes in the environment (Lin et al. 2002). Furthermore, moisture absorption by natural fibres affects their physical, mechanical, and thermal properties (Dhakal et al. 2007).
Natural fibres are known to have low thermal stability, as most fibres start to degrade above 200 °C. The processing temperature and operating conditions need to be carefully selected to avoid decomposition of lignocellulose materials, which will deter optimum performance of the composite. SPF has a thermal stability up to 222.8 °C, as reported by Ticoalu et al. (2014), and 210 °C, as reported by Ishak et al. (2012). Compared with coir as reported by Rosa et al. (2009) the lignocellulose materials start to degrade at 190 °C. A similar investigation on thermal properties of coir and sisal by Bismarck et al. (2001) showed that these fibres had an onset thermal degradation between 190 and 230 °C. The low degradation temperature of natural fibres is a serious challenge because these temperatures are mostly inadequate for processing composite with thermoplastic materials that have high processing temperatures (Azwa et al. 2013). Natural fibres are of low durability compared with synthetic fibre, but this can be improved considerably with treatment (Pickering et al. 2015). These drawbacks can result in composites with undesirable properties that make them be unsuitable for certain applications. Fibre treatments and matrix modification solve some of these drawbacks.
Treatment of sugar palm fibre
Natural fibres are generally hydrophilic due to the presence of hydroxyl groups throughout its structure, especially in cellulose and hemicellulose. To improve the properties and performance of natural fibres, it becomes necessary to impart hydrophobicity to the natural fibres. Several treatment methods had been studied in order to improve the interfacial adhesion property between fibres and surrounding matrix and concurrently to reduce water absorption of the fibres. The treatment methods of natural fibres are many and each has its own effect on the properties of the natural fibres. The most common treatments are alkaline, silane, acetylation, benzoylation, and permanganate treatments. These treatments were outlined by Kabir et al. (2012).
Alkaline Treatment
Alkaline treatment, also known as mercerization, is the most common treatment method of natural fibres. Its simplicity and effectiveness make it a popular approach for treating natural fibre with sodium hydroxide aqueous solution to improve fibre-matrix adhesion and reduce moisture absorption. Alkaline treatment is beneficial in reducing the moisture absorption and increasing the interfacial bonding between sugar palm fibre and matrix (Bachtiar et al. 2008; Sapuan et al. 2010; Ticoalu et al. 2014). This modification usually affects the morphology, mechanical properties, and thermal degradation of SPF. In all of these published reports, the diameter of the SPF decreased, which increased the aspect ratio. The increase in aspect ratio results in rough topography, which yields better adhesion and mechanical properties. Bachtiar et al. (2008) reported that both tensile strength and modulus were improved by treating SPF with 0.25 M and 0.5 M NaOH, though inconsistent results were noticed at high concentration, which was attributed to fibre damage. Sapuan et al. (2010) showed that 0.25 M NaOH was optimum, as it yields better results and improved flexural strength compared with untreated fibre. In another work, SPF was treated with 5% and 10% NaOH, which increased the tensile strength by 34.3% and 29.3%, respectively (Ticoalu et al. 2014). The samples in this experiment were soaked in diluted NaOH for 2 h, followed by rinsing and drying at 80 °C for approximately 4 h.
Seawater Treatment
Seawater is an effective surface treatment of natural fibres at virtually no cost. This can be done by soaking the fibre in seawater for some days. Seawater naturally contains 35 g of salt in every 1000 g or 1 litre of water. The treatment is achieved by removing the outer layer of hemicellulose and pectin, thereby improving interfacial bonding between fibre and matrix. Leman et al. (2008) showed that fibre treated with seawater for 30 days had its tensile strength improved by 67.26% compared with untreated fibre. Ishak et al. (2009) showed that the impact and flexural strength of SPF increase significantly after a soaking period of 30 days in seawater. Recently, Rashid et al.(2016) further confirmed that treatment of SPF with seawater yield positive improvement based on the physical and morphological characterization results presented.
Pre-impregnation Process
Matrix pre-impregnation is another process that promotes interfacial adhesion bonding between the hydrophilic fibre and hydrophobic polymer (Fung et al. 2003; Herrera-Franco and Valadez-Gonzalez 2004, 2005). The pre-impregnation process exploits the low viscosity of the incurred resin, and this facilitates the impregnation of the matrix into the pores and surface of the reinforcing fibre. The effect of impregnating SPF with thermoset resin on physical and mechanical properties was studied by Ishak et al. 2011b. Based on this research, the effect of the process was more pronounced on the physical properties rather than mechanical properties, which were marginally improved. Two thermoset resins, unsaturated polyester and phenol formaldehyde, were used for the vacuum resin impregnation process, but the latter showed superior results. There was significant improvement in physical properties, namely, water absorption and moisture content were recorded, but no significant changes in specific gravity. The effect of impregnation pressure was studied Ishak et al. (2011a); an impregnation pressure of 600 mmHg was optimum to improve both physical and tensile properties.
Sugar palm fibre reinforced polymer composite
SPF/Thermoplastic Composite
The early research on SPF-reinforced thermoplastic composite was done by Sapuan and Bachtiar (2012). The researchers studied the tensile strength and modulus of sugar palm fibre reinforced high impact polystyrene (HIPS) with five different fibre loadings (10, 20, 30, 40, and 50%). With increased fibre loading in the HIPS matrix, the tensile modulus increased at the expense of the tensile strength, which was attributed to poor compatibility of the fibre and matrix. The result was supported by SEM analysis that showed fibre pull-out, signifying poor adhesion between the hydrophilic fibre and hydrophobic high impact polystyrene. Bachtiar et al. (2012) studied mechanical and thermal properties of untreated SPF reinforced HIPS. The composite showed a high thermal stability compared with the control and good mechanical properties. Zahari et al.(2015) determined the water resistance and mechanical properties of SPF reinforced polypropylene. The fibre and polypropylene matrix were mixed at 190 °C using a roll mill mixer. The compound was crushed using a plastic granulator to get pellets. The pellets were vacuum dried and injection-moulded to produce the composite samples. The result indicated improved tensile strength and modulus with silane treatment, but the elongation at yield was almost constant for both treated and untreated fibres. Water absorption increased at high fibre contents but stabilised after 10 days.
SPF/Thermoset Polymer Composite
Thermoset polymers are dominantly used as matrices with sugar palm fibre. Epoxy, unsaturated polyester, and phenol formaldehyde are the reported matrices used by various researchers. Epoxy has excellent properties that make it the best matrix in many composites; some of these properties are good adhesion, low moisture absorption, and ease of processing (Mar 2008). Leman et al.(2005) fabricated SPF reinforced epoxy composites using a hand lay-up process. The impact strength of the long fibre reinforced epoxy composite was higher than chopped fibre reinforced epoxy composite. The tensile properties of the same composite increased with fibre loading of 10 and 15% but decreased with 20% fibre loading (Sastra et al. 2006). The effect of accelerated ageing on SPF reinforced epoxy was studied (Ali et al. 2010). The results indicated that the aged composite had an increase in tensile strength up to 50.4%, but its impact strength declined by 6.33%. Sahari et al. (2011) studied water resistance of SPF reinforced unsaturated polyester, and the composite was produced using compression moulding with 30% fibre loading. The results indicated that SPF reinforced unsaturated polyester had lower values of water absorption and thickness swelling of 0.65 and 0.76%, respectively.
Other Matrices Reinforced with SPF
Increasing environmental concern has generated interest in biocomposites and the development of environmentally friendly material that is fully biodegradable. The biocomposite is obtained by blending biodegradable polymers with lignocellulose fibres, which yields a 100% biodegradable composite. Biopolymers or biodegradable polymers can be classified as agro-polymers (starch, protein, etc.) and biodegradable thermoplastic (poly (lactic acid) PLA). The latter are also called biopolyesters and are mainly obtained from renewable resources. SPF has been used with both agro-polymers and biodegradable thermoplastic. Environmentally friendly composites derived from sugar palm tree have been studied (Sahari et al. 2013a). The biocomposite was produced using SPF and plasticized starch from sugar palm trees. The biomatrix was produced by mixing 70% starch with 30% glycerol. With increased fibre loading, the biocomposite showed increased tensile strength, tensile modulus, flexural strength, flexural modulus, and impact strength but decreased elongation at break. Similarly, the water absorption and moisture content decreased with increased fibre loading. Lignocellulose decomposition started at a lower temperature of 150 °C, which indicated low thermal stability.
Polylactic acid (PLA) is a bio-derived polymer used as a matrix material, while Ijuk fibre was used as reinforcing material by Chalid et al. (2015) to fabricate biocomposites using hot compression moulding. In this composite, the best values of tensile strength and modulus were obtained with 10% fibre loading. Because SPF is a natural fibre and 100% biodegradable, it accelerates the biodegradability when combined with PLA (Chłopek et al. 2010).
Properties of sPF reinforced polymer composite
Determination of Water Resistance
Natural fibre reinforced polymer composites absorb moisture in a humid environment or when immersed in water. The moisture absorbed by the composite causes it to swell and develop dimensional instability. This is attributed to the hydrophilic nature of the natural fibres. These behaviours are major challenges that limit the interior applications for composites, except for treated fibre or hybridised composite. Fibre contents and lack of surface treatment of the fibre are the two major causes of water uptake in natural fibre reinforced polymer composites (Azwa et al.2013). Fibre content or loading is directly proportional to water uptake; higher fibre loading allows more moisture absorption in the composite. This strong relationship between water absorption and fibre weight fraction was seen in a study of hemp fibre reinforced polypropylene (Hargitai et al. 2008). A composite with 30% fibre fraction had only 7% water absorption, whereas for 70% fibre weight fraction, the water uptake increased to 53%.
Leman et al. (2008) reported that untreated SPF reinforced epoxy composite plate with 20% fibre loading has higher moisture absorption than 10% fibre loading composite plates. The plates were both immersed in a controlled water bath at 40 °C for 33 days. Bachtiar et al. (2012) reported moisture absorption behaviour of SPF-HIPS composites. The specimens were immersed in a water at 25 °C for 24 h. At 10%, 20%, 30%, 40%, and 50% fibre loading, the moisture absorption was 0.9%, 1.3%, 1.5%, 2.8%, and 3.9%, respectively; thus, increased fibre loading resulted in increased moisture absorption. The water absorption in natural fibre composite increases with the increase of fibre loading. This result contradicts the case of SPF reinforced biopolymer from sugar palm starch (SPS) as a matrix (Sahari et al. 2013a). The results indicate that with an increase of SPF loading, the moisture absorption of the composite decreases. This phenomenon was attributed to the fact that SPF is more hydrophobic than plasticized sugar palm starch.
The moisture absorption characteristic of sugar palm fibre reinforced polymer composites was reviewed. The percentage of moisture uptake clearly increases as the fibre volume fraction increases. This was attributed to the presence of high cellulose in the SPF. This drawback is the main reason for it being precluded in exterior applications. Surface treatments and matrix modification are considered the general solutions to this weakness in natural fibres, which can also be applied to SPF.
Mechanical Properties
The mechanical properties of SPF reinforced polymer composites—namely, tensile properties, flexural properties, and impact properties—are noticeably altered by the fibre weight fraction, fibre treatment, and/or matrix modification. Table 7 shows the tensile properties of the novel sugar palm fibre reinforced polymer composites and the matrices used. Many natural fibre composites show variation or inconsistent values in these properties, which were attributed to the source of the fibre, processing, or manufacturing techniques.
Table 7. Tensile Properties of Sugar Palm Fibre Reinforced Polymer Composites
The mechanical properties of SPF-reinforced polymer composites have been studied (Sastra et al.2006; Suriani et al. 2007; Bachtiar et al. 2008; Sapuan and Bachtiar 2012; Oumer and Bachtiar 2014; Zahari et al. 2015). Different fibre forms, i.e., long, chopped, and woven, were used with different types of polymer matrices.
Irrespective of processing methods and other factors, woven sugar palm fibre reinforced epoxy presented a superior value of tensile strength of 51.7 MPa (Suriani et al. 2007). Long fibre with 10 wt.% loading reinforced epoxy had the highest tensile modulus of 3780 MPa (Bachtiar et al.2008), which was attributed to the mercerization treatment of SPF. This showed that chemical treatment offers better physical and mechanical properties. In the same experiment, 0.25 M NaOH and a 1-h soaking time were the optimised alkaline treatment parameters. A similar trend was noticed with treatments using seawater and fresh water; the mechanical properties were slightly improved (Leman et al. 2008; Ishak et al. 2009).
The tensile modulus was considerably increased when high impact polystyrene was used as the matrix (Sapuan and Bachtiar 2012; Oumer and Bachtiar 2014). The addition of SPF to HIPS decreases the tensile strength, and a similar trend was reported by Antich et al. (2006) for sisal fibre reinforced HIPS. Generally, irrespective of fibre loading, the fibre form in SPF reinforced polymer composites has a tensile strength of 17.57 to 51.7 MPa and tensile modulus of 361.32 to 3780 MPa.
The cited work reflected that with an increase of fibre fraction, the tensile strength increases to a maximum value and later drops. A similar trend is observed for the tensile modulus, though in some research the values either fluctuate or decrease. Some factors contributing to this variation are fabrication method, fibre degradation, and lack of interfacial adhesion. The evaluation of the performance of natural fibre composites should not be restricted to mechanical properties. The best is to make use of ternary diagram as proposed by Koronis et al. (2013), which includes specific strength, specific stiffness and cost per weight for evaluating the performance of particular composites.
Thermogravimetric analysis of SPF-reinforced composite
The growing interest in using SPF as reinforcement in polymer composites has motivated the investigation of the thermal behaviour of the composites, though not much has been reported on thermogravimetric analysis of SPF-reinforced polymer composites. Bachtiar et al. (2012) reported TGA and DTG thermograms of SPF-reinforced HIPS composite. The thermograms were obtained at a heating rate of 20 °C/min, and the samples were observed from 30 to 600 °C. High thermal stability of the composite was noticed with degradation commencing at 329 °C and completed at 447 °C. The results indicated that the thermal stability increases with the increased fibre loading. The same trend was noticed in a fully biodegradable composite of SPF and biopolymer from sugar palm starch (Sahari et al. 2013a).
The first mass loss occurs between 30 to 100 °C for the moisture evaporation, while the major constituents decomposed between 150 and 380 °C. Thermal stability of the composite increases with the increased fibre loading, which was clearly seen from the percentage of the residue or ash of the various composites. The findings of the thermal analysis of SPF-reinforced polymer is supported by the work of Santafé et al. (2011). They reported that the TG curves of untreated coir reinforced polyester composite at different fibre loading (10, 20, and 30 wt.%) showed an onset of degradation at approximately 340 °C and completed at 450 °C.
Applications and potentials of natural fibre composites
To minimise dependency on exhaustible fossil products and reduce environmental impact, composites from renewable resources have been very promising mostly in the automotive and aerospace industries. In automobiles, the dominant use of natural fibre composites by far is in the interior parts. They are utilised in the interior because natural fibre composites absorb moisture in a humid climate and tend to swell. Swelling leads to tiny cracks forming between the fibre and matrix, allowing water molecules to infiltrate. This phenomenon makes the composite degrade and lose strength easily. Despite these drawbacks, natural fibre composites are preferred over synthetic fibre composites. German car manufacturers are in the forefront for utilising natural fibre composites in many components of automobiles including door panels, seat shells, shelf trim panels, roof liners, and package trays. There are few exterior automotive components being used including tire covers, under-the-hood radiator end tank, car disc brakes, and under-body panels (Hill et al. 2012). Other applications include the aerospace, furniture, consumer goods, and package industries. Polypropylene based composites produced by compression moulding, injection moulding, or thermoforming extruded sheet are favoured in automotive applications (Puglia et al. 2005).
Sugar palm fibre has started gaining acceptance in engineering applications. A new material, a hybrid of sugar palm fibre and glass-reinforced unsaturated polyester, was used to manufacture a small boat (Fig. 8(a); Misri et al. 2010). The hybrid small boat had its mechanical properties increased significantly with a tensile modulus of 1840.6 MPa and impact strength of 2.471 kJ/m2. In addition to the increased mechanical properties, the weight was reduced by 50% with the substitution of sugar palm fibre in place of glass fibre (Sanyang et al. 2016b). Sugar palm fibre (Ijuk) reinforced thermoset was studied in helmets as well, as shown in Fig. 8(b) (Zaid 2009). The helmet passed Malaysian standard (MS) test conducted by SIRIM QAS INT., Sdn. Bhd. In another development, a zinc roofing sheet was lined with sugar palm fibre as sound proofing material (Imran 2015). The same material could be utilised potentially for sound proofing engine covers. With ongoing research, more potential uses of sugar palm fibre and its composites will be explored and used in many applications.
Fig. 8. SPF product development (a) small boat and (b) safety helmet (Zaid 2009; Misri et al.2010)
Conclusions
- Sugar palm trees are a novel source of natural fibre with ecological and economic advantages. This low density, biodegradable fibre can be used with a polymeric material to produce partially biodegradable composites.
- The starch from sugar palm tree can be utilised to produce biopolymer, which can be used with natural fibre to produce a “biocomposite” or “green composite”. It can also be chemically modified by plasticizing into films for food packaging.
- The sugar palm sap is used as a drink or as a raw material for nectar sweetener. It is also fermented to produce biofuel, namely bioethanol.
- Properties of the sugar palm fibre are within the range of natural fibres, which make it qualify as reinforcement in natural fibre composites. Based on the available information, sugar palm fibre has a diameter of 81 to 500 µm, cellulose content of between 37.3 to 66.5%, hemicellulose content of 4.7 to 20.6%, and lignin content of 17.9 to 46.4%.
- Further research on sugar palm fibre should focus on the influence of SPF incorporation on the properties of synthetic fibres, for possible used in structural applications.
REFERENCES CITED
Ali, A., Sanuddin, A., and Ezzeddin, S. (2010). “The effect of aging on Arenga pinnata fiber-reinforced epoxy composite,” Materials & Design 31(7), 3550-3554. DOI: 10.1016/j.matdes.2010.01.043
Antich, P., Vázquez, A., Mondragon, I., and Bernal, C. (2006).”Mechanical behavior of high impact polystyrene reinforced with short sisal fibers,” Composites Part A: Applied Science and Manufacturing 37(1), 139-150. DOI: 10.1016/j.compositesa.2004.12.002
Ayrilmis, N., Jarusombuti, S., Fueangvivat, V., Bauchongkol, P., and White, R. H. (2011). “Coir fiber reinforced polypropylene composite panel for automotive interior applications,” Fibers and Polymers 12(7), 919-926. DOI: 10.1007/s12221-011-0919-1
Azwa, Z., Yousif, B., Manalo, A., and Karunasena, W. (2013). “A review on the degradability of polymeric composites based on natural fibres,” Materials & Design 47, 424-442. DOI: 10.1016/j.matdes.2012.11.025
Bachtiar, D., Salit, M. S., Zainuddin, E., Abdan, K., and Dahlan, K. Z. H. M. (2011). “Effects of alkaline treatment and a compatibilizing agent on tensile properties of sugar palm fibre-reinforced high impact polystyrene composites,” BioResources 6(4), 4815-4823. DOI: 10.15376/biores.6.4.4815-4823
Bachtiar, D., Sapuan, S., and Hamdan, M. (2008). “The effect of alkaline treatment on tensile properties of sugar palm fibre reinforced epoxy composites,” Materials & Design 29(7), 1285-1290. DOI: 10.1016/j.matdes.2007.09.006
Bachtiar, D., Sapuan, S., Khalina, A., Zainudin, E., and Dahlan, K. (2012). “The flexural, impact and thermal properties of untreated short sugar palm fibre reinforced high impact polystyrene (HIPS) composites,” Polymers & Polymer Composites 20(5), 493.
Bachtiar, D., Sapuan, S., Zainudin, E. S., Khalina, A., and Dahlan, K. (2010). “The tensile properties of single sugar palm (Arenga pinnata) fibre,” IOP Conference Series: Materials Science and Engineering 11(2010), Article ID 012012. DOI: 10.1088/1757-899x/11/1/012012
Baley, C. (2002). “Analysis of the flax fibres tensile behaviour and analysis of the tensile stiffness increase,” Composites Part A: Applied Science and Manufacturing 33(7), 939-948. DOI: 10.1016/S1359-835X(02)00040-4
Birnin-Yauri, A. U., Ibrahim, N. A., Zainuddin, N., Abdan, K., Then, Y. Y., and Chieng, B. W. (2016a). “Enhancement of the Mechanical Properties and Dimensional Stability of Oil Palm Empty Fruit Bunch-Kenaf Core and Oil Palm Mesocarp-Kenaf Core Hybrid Fiber-Reinforced Poly (lactic acid) Biocomposites by Borax Decahydrate Modification of Fibers,” BioResources 11(2), 4865-4884. DOI: 10.15376/biores.11.2.4865-4884
Birnin-Yauri, A. U., Ibrahim, N. A., Zainuddin, N., Abdan, K., Then, Y. Y., and Chieng, B. W. (2016b). “Influence of kenaf core fiber incorporation on the mechanical performance and dimensional stability of oil palm fiber reinforced poly (lactic acid) hybrid biocomposites,” BioResources 11(2), 3332-3355. DOI: 10.15376/biores.11.2.3332-3355
Bismarck, A., Mohanty, A. K., Aranberri-Askargorta, I., Czapla, S., Misra, M., Hinrichsen, G., and Springer, J. (2001). “Surface characterization of natural fibers; surface properties and the water up-take behavior of modified sisal and coir fibers,” Green Chemistry 3(2), 100-107. DOI: 10.1039/b100365h
Bledzki, A., and Gassan, J. (1999). “Composites reinforced with cellulose based fibres.” Progress in Polymer Science 24(2), 221-274. DOI: 10.1016/S0079-6700(98)00018-5
Bogoeva‐Gaceva, G., Avella, M., Malinconico, M., Buzarovska, A., Grozdanov, A., Gentile, G., and Errico, M. E. (2007). “Natural fiber eco‐composites,” Polymer Composites 28(1), 98-107. DOI: 10.1002/pc.20270
Chalid, M., and Prabowo, I. (2015). “The effects of alkalization to the mechanical properties of the ijuk fiber reinforced PLA biocomposites,” International Journal of Chemical, Nuclear, Material and Metallurgical Engineering 9(2), 342-346.
Chalid, M., Rahman, A., Ferdian, R., and Priyono, B. (2015). “On the tensile properties of polylactide (PLA)/Arenga pinnata “ijuk” fibre composite,” Macromolecular Symposia 353(1), 108-114. DOI: 10.1002/masy.201550314
Chłopek, J., Morawska-Chochół, A., and Szaraniec, B. (2010). “The influence of the environment on the degradation of polylactides and their composites,” Journal of Achievements in Materials and Manufacturing Engineering 43(1), 72-79.
Defoirdt, N., Biswas, S., De Vriese, L., Van Acker, J., Ahsan, Q., Gorbatikh, L., van Vuure, A. W., and Verpoest, I. (2010). “Assessment of the tensile properties of coir, bamboo and jute fibre,” Composites Part A: Applied Science and Manufacturing 41(5), 588-595. DOI: 10.1016/j.compositesa.2010.01.005
Dhakal, H., Zhang, Z., and Richardson, M. (2007). “Effect of water absorption on the mechanical properties of hemp fibre reinforced unsaturated polyester composites,” Composites Science and Technology 67(7), 1674-1683. DOI: 10.1016/j.compscitech.2006.06.019
Dransfield, J., Uhl, N. W., Asmussen, C. B., Baker, W. J., Harley, M. M., and Lewis, C. E. (2005). “A new phylogenetic classification of the palm family, Arecaceae,” Kew Bulletin 559-569.
Faruk, O., Bledzki, A. K., Fink, H. P., and Sain, M. (2014). “Progress report on natural fiber reinforced composites,” Macromolecular Materials and Engineering 299(1), 9-26. DOI: 10.1002/mame.201300008
Fung, K., Xing, X., Li, R., Tjong, S., and Mai, Y.-W. (2003). “An investigation on the processing of sisal fibre reinforced polypropylene composites,” Composites Science and Technology 63(9), 1255-1258. DOI: 10.1016/S0266-3538(03)00095-2
Garkhail, S., Heijenrath, R., and Peijs, T. (2000). “Mechanical properties of natural-fibre-mat-reinforced thermoplastics based on flax fibres and polypropylene,” Applied Composite Materials 7(5-6), 351-372. DOI: 10.1023/A:1026590124038
Han, J. S., and Rowell, J. S. (1997). “Chemical composition of fibers,” in: Paper and Composites from Agro-Based Resources, CRC Press, Boca Raton, FL, 83-134.
Hargitai, H., Rácz, I., and Anandjiwala, R. D. (2008). “Development of hemp fiber reinforced polypropylene composites,” Journal of Thermoplastic Composite Materials 21(2), 165-174. DOI: 10.1177/0892705707083949
Herrera-Franco, P., and Valadez-Gonzalez, A. (2004). “Mechanical properties of continuous natural fibre-reinforced polymer composites,” Composites Part A: Applied Science and Manufacturing 35(3), 339-345. DOI: 10.1016/j.compositesa.2003.09.012
Herrera-Franco, P., and Valadez-Gonzalez, A. (2005). “A study of the mechanical properties of short natural-fiber reinforced composites,” Composites Part B: Engineering 36(8), 597-608. DOI: 10.1016/j.compositesb.2005.04.001
Heyne, K. (1950). De Nuttige planten van Indonesie [The useful plants in Indonesia], Van Hoeve S., Bandung, Indonesia.
Hill, K., Swiecki, B., and Cregger, J. (2012). The Bio-based Materials Automotive Value Chain, Center for Automotive Research, Economic Development and Strategies Group, Washington, DC.
Ho, M.-p., Wang, H., Lee, J.-H., Ho, C.-k., Lau, K.-t., Leng, J., and Hui, D. (2012). “Critical factors on manufacturing processes of natural fibre composites,” Composites Part B: Engineering 43(8), 3549-3562. DOI: 10.1016/j.compositesb.2011.10.001
Holbery, J., and Houston, D. (2006). “Natural-fiber-reinforced polymer composites in automotive applications,” Jom 58(11), 80-86. DOI: 10.1007/s11837-006-0234-2
Imran, M. (2015). Sound Insulation and Vibration Reduction of Modified Zinc Roof using Natural Fiber (Arenga pinnata), Master’s Thesis, Universiti Tun Hussein Onn Malaysia, Johor, Malaysia.
Imre, B., and Pukánszky, B. (2013). “Compatibilization in bio-based and biodegradable polymer blends,” European Polymer Journal 49(6), 1215-1233. DOI: 10.1016/j.eurpolymj.2013.01.019
Ishak, M., Leman, Z., Sapuan, S., Rahman, M., and Anwar, U. (2011a). “Effects of impregnation pressure on physical and tensile properties of impregnated sugar palm (Arenga pinnata) fibres,”Key Engineering Materials 471-472, 1153-1158. DOI: 10.4028/www.scientific.net/kem.471-472.1153
Ishak, M., Leman, Z., Sapuan, S., Rahman, M., and Anwar, U. (2011b). “Effects of impregnation time on physical and tensile properties of impregnated sugar palm (Arenga pinnata) fibres.” Key Engineering Materials 471-472, 1147-1152. DOI: DOI: 10.4028/www.scientific.net/kem.471-472.1147
Ishak, M., Leman, Z., Sapuan, S., Rahman, M., and Anwar, U. (2013). “Chemical composition and FT-IR spectra of sugar palm (Arenga pinnata) fibers obtained from different heights,” Journal of Natural Fibers 10(2), 83-97. DOI: 10.1080/15440478.2012.733517
Ishak, M., Leman, Z., Sapuan, S., Salleh, M., and Misri, S. (2009). “The effect of sea water treatment on the impact and flexural strength of sugar palm fibre reinforced epoxy composites,” International Journal of Mechanical and Materials Engineering (IJMME) 4(3), 316-320.
Ishak, M., Sapuan, S., Leman, Z., Rahman, M., and Anwar, U. (2012). “Characterization of sugar palm (Arenga pinnata) fibres,” Journal of Thermal Analysis and Calorimetry 109(2), 981-989. DOI: 10.1007/s10973-011-1785-1
Ishak, M., Sapuan, S., Leman, Z., Rahman, M., Anwar, U., and Siregar, J. (2013). “Sugar palm (Arenga pinnata): Its fibres, polymers and composites,” Carbohydrate Polymers 91(2), 699-710. DOI: 10.1016/j.carbpol.2012.07.073
Jawaid, M., and Khalil, H. A. (2011). “Cellulosic/synthetic fibre reinforced polymer hybrid composites: A review,” Carbohydrate Polymers 86(1), 1-18. DOI: 10.1016/j.carbpol.2011.04.043
Joshi, S. V., Drzal, L., Mohanty, A., and Arora, S. (2004). “Are natural fiber composites environmentally superior to glass fiber reinforced composites?” Composites Part A: Applied Science and Manufacturing 35(3), 371-376. DOI: 10.1016/j.compositesa.2003.09.016
Kabir, M., Wang, H., Lau, K., and Cardona, F. (2012). “Chemical treatments on plant-based natural fibre reinforced polymer composites: An overview,” Composites Part B: Engineering 43(7), 2883-2892. DOI: 10.1016/j.compositesb.2012.04.053
Kalia, S., Dufresne, A., Cherian, B. M., Kaith, B., Avérous, L., Njuguna, J., and Nassiopoulos, E. (2011). “Cellulose-based bio-and nanocomposites: A review,” International Journal of Polymer Science 2011, 35. DOI: 10.1155/2011/837875
Kalia, S., Kaith, B., and Kaur, I. (2009). “Pretreatments of natural fibers and their application as reinforcing material in polymer composites—A review,” Polymer Engineering & Science 49(7), 1253-1272. DOI: 10.1002/pen.21328
Koronis, G., Silva, A., and Fontul, M. (2013). “Green composites: A review of adequate materials for automotive applications.” Composites Part B: Engineering 44(1), 120-127. DOI: 10.1016/j.compositesb.2012.07.004
Ku, H., Wang, H., Pattarachaiyakoop, N., and Trada, M. (2011). “A review on the tensile properties of natural fiber reinforced polymer composites,” Composites Part B: Engineering 42(4), 856-873. DOI: 10.1016/j.compositesb.2011.01.010
Lawoko, M., Henriksson, G., and Gellerstedt, G. (2005). “Structural differences between the lignin-carbohydrate complexes present in wood and in chemical pulps,” Biomacromolecules 6(6), 3467-3473. DOI: 10.1021/bm058014q
Leman, Z., Sapuan, S., Azwan, M., Ahmad, M. M. H. M., and Maleque, M. (2008). “The effect of environmental treatments on fiber surface properties and tensile strength of sugar palm fiber-reinforced epoxy composites,” Polymer-Plastics Technology and Engineering 47(6), 606-612. DOI: 10.1080/03602550802059451
Leman, Z., Sapuan, S., Ishak, M., and Ahmad, M. (2010). “Pre-treatment by water retting to improve the interfacial bonding strength of sugar palm fibre reinforced epoxy composite,” Polymers from Renewable Resources 1(1), 35.
Leman, Z., Sapuan, S., Saifol, A., Maleque, M. A., and Ahmad, M. (2008). “Moisture absorption behavior of sugar palm fiber reinforced epoxy composites,” Materials & Design 29(8), 1666-1670. DOI: 10.1016/j.matdes.2007.11.004
Leman, Z., Sastra, H., Sapuan, S., Hamdan, M., and Maleque, M. (2005). “Study on impact properties of Arenga pinnata fibre reinforced epoxy composites,” Journal Teknologi Terpakai 3(1), 14-19.
Li, X., Tabil, L. G., and Panigrahi, S. (2007). “Chemical treatments of natural fiber for use in natural fiber-reinforced composites: A review,” Journal of Polymers and the Environment 15(1), 25-33. DOI: 10.1007/s10924-006-0042-3
Lin, Q., Zhou, X., and Dai, G. (2002). “Effect of hydrothermal environment on moisture absorption and mechanical properties of wood flour–filled polypropylene composites,” Journal of Applied Polymer Science 85(14), 2824-2832. DOI: 10.1002/app.10844
Malkapuram, R., Kumar, V., and Negi, Y. S. (2008). “Recent development in natural fiber reinforced polypropylene composites,” Journal of Reinforced Plastics and Composites 28(10), 1169-1189. DOI: 10.1177/0731684407087759
Mar, P. (2008). “Matrices for natural-fibre reinforced composites,” in: Properties and Performance of Natural-Fibre Composites, K. L. Pickering (ed.), Woodhead Publishing Limited, Cambridge England, pp. 67-126.
Martin, N., Mouret, N., Davies, P., and Baley, C. (2013). “Influence of the degree of retting of flax fibers on the tensile properties of single fibers and short fiber/polypropylene composites,” Industrial Crops and Products 49, 755-767. DOI: 10.1016/j.indcrop.2013.06.012
McKendry, P. (2002). “Energy production from biomass (part 1): Overview of biomass,” Bioresource Technology 83(1), 37-46. DOI: 10.1016/S0960-8524(01)00118-3
Misri, S., Leman, Z., Sapuan, S., and Ishak, M. (2010). “Mechanical properties and fabrication of small boat using woven glass/sugar palm fibres reinforced unsaturated polyester hybrid composite,” IOP Conference Series: Materials Science and Engineering 11(2010), Article ID 012015. DOI: 10.1088/1757-899x/11/1/012015
Mogea, J., Seibert, B., and Smits, W. (1991). “Multipurpose palms: The sugar palm (Arenga pinnata (Wurmb) Merr.),” Agroforestry Systems 13(2), 111-129. DOI: 10.1007/BF00140236
Munawar, S. S., Umemura, K., and Kawai, S. (2007). “Characterization of the morpho-logical, physical, and mechanical properties of seven nonwood plant fiber bundles,” Journal of Wood Science 53(2), 108-113. DOI: 10.1007/s10086-006-0836-x
Mwaikambo, L., and Ansell, M. (2006). “Mechanical properties of alkali treated plant fibres and their potential as reinforcement materials. I. Hemp fibres,” Journal of Materials Science 41(8), 2483-2496. DOI: 10.1007/s10853-006-5098-x
Omrani, E., Menezes, P. L., and Rohatgi, P. K. (2015). “State of the art on tribological behavior of polymer matrix composites reinforced with natural fibers in the green materials world,” Engineering Science and Technology 19(2), 717-736. DOI: 10.1016/j.jestch.2015.10.007
Oumer, A., and Bachtiar, D. (2014). “Modeling and experimental validation of tensile properties of sugar palm fiber reinforced high impact polystyrene composites,” Fibers and Polymers 15(2), 334-339. DOI: 10.1007/s12221-014-0334-5
Paul, A., Joseph, K., and Thomas, S. (1997). “Effect of surface treatments on the electrical properties of low-density polyethylene composites reinforced with short sisal fibers,” Composites Science and Technology 57(1), 67-79. DOI: 10.1016/S0266-3538(96)00109-1
Pérez, J., Munoz-Dorado, J., de la Rubia, T., and Martinez, J. (2002). “Biodegradation and biological treatments of cellulose, hemicellulose, and lignin: An overview,” International Microbiology 5(2), 53-63. DOI: 10.1007/s10123-002-0062-3
Pickering, K., Efendy, M. A., and Le, T. (2015). “A review of recent developments in natural fibre composites and their mechanical performance,” Composites Part A: Applied Science and Manufacturing 83(special issue), 98-112. DOI: 10.1016/j.compositesa.2015.08.038
Puglia, D., Biagiotti, J., and Kenny, J. (2005). “A review on natural fibre-based composites—Part II: Application of natural reinforcements in composite materials for automotive industry,” Journal of Natural Fibers 1(3), 23-65. DOI: 10.1300/J395v01n03_03
Rao, K. M. M., and Rao, K. M. (2007). “Extraction and tensile properties of natural fibers: Vakka, date and bamboo,” Composite Structures 77(3), 288-295. DOI: 10.1016/j.compstruct.2005.07.023
Rashid, B., Leman, Z., Jawaid, M., Ghazali, M., and Ishak, M. (2016). “Physicochemical and thermal properties of lignocellulosic fiber from sugar palm fibers: Effect of treatment,” Cellulose23(5), 2905-2916. DOI: 10.1007/s10570-016-1005-z
Razak, H. A., and Ferdiansyah, T. (2005). “Toughness characteristics of Arenga pinnata fibre concrete,” Journal of Natural Fibers 2(2), 89-103. DOI: 10.1300/J395v02n02_06
Reddy, N., and Yang, Y. (2005). “Biofibers from agricultural byproducts for industrial applications,” TRENDS in Biotechnology 23(1), 22-27. DOI: 10.1016/j.tibtech.2004.11.002
Rong, M. Z., Zhang, M. Q., Liu, Y., Yang, G. C., and Zeng, H. M. (2001). “The effect of fiber treatment on the mechanical properties of unidirectional sisal-reinforced epoxy composites,” Composites Science and Technology 61(10), 1437-1447. DOI: 10.1016/S0266-3538(01)00046-X
Rosa, M. F., Chiou, B.-s., Medeiros, E. S., Wood, D. F., Williams, T. G., Mattoso, L. H., Orts, W. J., and Imam, S. H. (2009). “Effect of fiber treatments on tensile and thermal properties of starch/ethylene vinyl alcohol copolymers/coir biocomposites,” Bioresource Technology 100(21), 5196-5202. DOI: 10.1016/j.biortech.2009.03.085
Rowell, R. M. (2008). “Natural fibres: types and properties,” in: Properties and Performance of Natural-Fibre Composites, K. L. Pickering (ed.), Woodhead Publishing Limited, Cambridge England, pp. 3-66.
Sahari, J., Sapuan, S., Ismarrubie, Z., and Rahman, M. (2011). “Comparative study of physical properties based on different parts of sugar palm fibre reinforced unsaturated polyester composites,” Key Engineering Materials 471-472, 455-460. DOI: 10.4028/www.scientific.net/kem.471-472.455
Sahari, J., Sapuan, S., Ismarrubie, Z., and Rahman, M. (2012). “Physical and chemical properties of different morphological parts of sugar palm fibres,” Fibres & Textiles in Eastern Europe 20(2), 21-24.
Sahari, J., Sapuan, S., Zainudin, E., and Maleque, M. (2012a). “A new approach to use Arenga pinnata as sustainable biopolymer: Effects of plasticizers on physical properties,” Procedia Chemistry 4, 254-259. DOI: 10.1016/j.proche.2012.06.035
Sahari, J., Sapuan, S., Zainudin, E., and Maleque, M. (2012b). “Sugar palm tree: A versatile plant and novel source for biofibres, biomatrices, and biocomposites,” Polymers from Renewable Resources 3(2), 61.
Sahari, J., Sapuan, S., Zainudin, E., and Maleque, M. A. (2013a). “Mechanical and thermal properties of environmentally friendly composites derived from sugar palm tree,” Materials & Design 49, 285-289. DOI: 10.1016/j.matdes.2013.01.048
Sahari, J., Sapuan, S., Zainudin, E., and Maleque, M. A. (2013b). “Thermo-mechanical behaviors of thermoplastic starch derived from sugar palm tree (Arenga pinnata),” Carbohydrate Polymers 92(2), 1711-1716. DOI: 10.1016/j.carbpol.2012.11.031
Santafé, H. P., Rodriguez, R. J., Monteiro, S. N., and Castillo, T. E. (2011). “Characterization of thermogravimetric behavior of polyester composites reinforced with coir fiber,” in: EPD Congress, S. N. Monteiro, D. E. Verhulst, P. N. Anyalebechi, and J. A. Pomykala (eds.), John Wiley & Sons, Hoboken, NJ, USA. DOI: 10.1002/9781118495285.ch37
Sanyang, M., Sapuan, S., Jawaid, M., Ishak, M., and Sahari, J. (2015). “Effect of plasticizer type and concentration on tensile, thermal and barrier properties of biodegradable films based on sugar palm (Arenga pinnata) starch,” Polymers 7(6), 1106-1124. DOI: 10.3390/polym7061106
Sanyang, M., Sapuan, S., Jawaid, M., Ishak, M., and Sahari, J. (2016a). “Effect of plasticizer type and concentration on physical properties of biodegradable films based on sugar palm (Arenga pinnata) starch for food packaging,” Journal of Food Science and Technology 53(1), 326-336. DOI: 10.1007/s13197-015-2009-7
Sanyang, M., Sapuan, S., Jawaid, M., Ishak, M., and Sahari, J. (2016b). “Recent developments in sugar palm (Arenga pinnata) based biocomposites and their potential industrial applications: A review,” Renewable and Sustainable Energy Reviews 54, 533-549. DOI: 10.1016/j.rser.2015.10.037
Sapuan, S., and Bachtiar, D. (2012). “Mechanical properties of sugar palm fibre reinforced high impact polystyrene composites,” Procedia Chemistry 4, 101-106. DOI: 10.1016/j.proche.2012.06.015
Sapuan, S., Bachtiar, D., and Hamdan, M. (2010). “Flexural properties of alkaline treated sugar palm fibre reinforced epoxy composites,” International Journal of Automotive and Mechanical Engineering (IJAME) 1, 79-90. DOI: 10.15282/ijame.1.2010.7.0007
Sastra, H., Siregar, J., Sapuan, S. M., and Hamdan, M. (2006). “Tensile properties of Arenga pinnata fiber-reinforced epoxy composites,” Polymer-Plastics Technology and Engineering 45(1), 149-155. DOI: 10.1080/03602550500374038
Scheller, H. V., and Ulvskov, P. (2010). “Hemicelluloses,” Plant Biology 61(1), 263. DOI: 10.1146/annurev-arplant-042809-112315
Senwitz, C., Kempe, A., Neinhuis, C., Mandombe, J. L., Branquima, M. F., and Lautenschlӓger, T. (2016) “Almost forgotten resources-biomechanical properties of traditionally used bast fibers from Northern Angola,” BioResources 11(3), 7595-7607. DOI: 10.15376/biores.11.3.7595-7607
Suriani, M., Hamdan, M., Sastra, H., and Sapuan, S. (2007). “Study of interfacial adhesion of tensile specimens of Arenga pinnata fiber reinforced composites,” Multidiscipline Modeling in Materials and Structures 3(2), 213-224. DOI: 10.1163/157361107780744360
Suwartapradja, O. S. (2003). “Arenga pinnata: A case study of indigenous knowledge on the utilization of a wild food plant in West Java,” (https://arenindonesia.wordpress.com/makalah-aren/opan-s-suwartapradja/), Accessed 30 Apr 2016.
Ticoalu, A., Aravinthan, T., and Cardona, F. (2014). “A study into the characteristics of gomuti (Arenga pinnata) fibre for usage as natural fibre composites,” Journal of Reinforced Plastics and Composites 33(2), 179-192. DOI: 10.1177/0731684413503191
Wambua, P., Ivens, J., and Verpoest, I. (2003). “Natural fibres: Can they replace glass in fibre reinforced plastics? ,” Composites Science and Technology 63(9), 1259-1264. DOI: 10.1016/S0266-3538(03)00096-4
Wanderer, B. (2010). “PalmScapes,” (http://palmscapes.blogspot.my/2010_06_01_archive.html), Accessed 27 Mar 2016.
Yang, H., Yan, R., Chen, H., Lee, D. H., and Zheng, C. (2007). “Characteristics of hemicellulose, cellulose and lignin pyrolysis,” Fuel 86(12), 1781-1788. DOI: 10.1016/j.fuel.2006.12.013
Yevich, R., and Logan, J. A. (2003). “An assessment of biofuel use and burning of agricultural waste in the developing world,” Global Biogeochemical Cycles 17(4) , DOI: 10.1029/2002GB001952
Zahari, W., Badri, R., Ardyananta, H., Kurniawan, D., and Nor, F. (2015). “Mechanical properties and water absorption behavior of polypropylene/ijuk fiber composite by using silane treatment,” Procedia Manufacturing 2, 573-578. DOI: 10.1016/j.promfg.2015.07.099
Zaid, A. M. B. A. (2009). “Ijuk-natural fibre reinforced composite (I-NaFReC),” in: International Invention, Innovation and Technology Exhibition 2009 (ITEX’09), Universiti Tun Hussein Onn Malaysia (UTHM), Johor, Malaysia.
Article submitted: August 30, 2016; Peer review completed: October 23, 2016; Revised version received and accepted: October 27, 2016; Published: November 1, 2016.
DOI: 10.15376/biores.11.4.10756-10782