Research Articles

Generation of lignin-carbohydrate complex (LCC) between dehydrogenation polymer (DHP) and pulp fibers may have an important impact on the properties of pulp. In this work, the benzyl ester-type LCC was formed between oxidized cellulose and DHP. The effect of pH on the addition reaction of oxidized cellulose to quinone methide in the synthesis of DHP-cellulose complex (DHPCC) was investigated. The structure of the product was characterized by Fourier Transform Infrared (FTIR), Carbon 13-Nuclear Magnetic Resonance (¹³C-NMR), and 2-Dimensional Heteronuclear Single Quantum Coherence Nuclear Magnetic Resonance (2D HSQC NMR) analyses. The results indicated that cellulose was indeed oxidized and carboxyl groups were introduced into cellulose by the oxidation process. The formed DHPCC was connected by benzyl ester linkage. In addition, the pH of the reaction system had an important role in the formation of the benzyl ester bonds. The acidic condition (pH = 4.0) was conducive to the addition reaction of quinone methide with carboxyl groups of cellulose. Overall, this study provides helpful guidance for the generation of LCC between DHP and paper pulp fibers.

The disposal of agricultural waste ash is a great ecological challenge. This study analyzed the basic properties of corn straw ash and soybean straw ash, encompassing the identification of key oxides, the assessment of particle size distribution, and the performance of thermogravimetric analysis. This study also evaluated the potential of corn straw ash and soybean straw ash to replace cement in mortar and concrete through laboratory tests. The findings indicated that the strength activity index of corn straw ash was higher than soybean straw ash. Furthermore, when these ashes were used as cement replacements, the compressive strength of concrete decreased. Notably, concrete containing corn straw ash exhibited greater strength than concrete with the same substitution amount of soybean straw ash. Specifically, at a 5% substitution level, the compressive strengths of corn straw ash concrete and soybean straw ash concrete were 31.5 and 30.5 MPa, respectively. Additionally, soybean straw ash concrete demonstrated superior resistance to water penetration compared to corn straw ash concrete. Both corn straw ash and soybean straw ash exhibited the potential to enhance the early crack resistance of concrete.

The purpose of this study was to use ultrasound-based extraction to prepare starch from the tubers of Cyperus esculentus. Ultrasonic treatment of Cyperus esculentus powder with a medium of alkaline-treated water can effectively improve the starch extraction efficiency. Box-Behnken design was used to optimize the extraction process, and the results showed that the optimal parameters were ultrasound time of 30 minutes, pH value of 9.0, ultrasound temperature of 40 °C, and solid-liquid ratio of 10:1. The extraction percentage under these conditions was 90.1%. The physicochemical properties of C. esculentus starch were compared with those of cassava, potato, and corn starch. The particle size of C. esculentus starch was approximately 2 to 15 μm. The gelatinization temperature was 70.5 °C, and the peak viscosity was similar to cassava but with better thermal stability. Like other tuber starches, C. esculentus starch had higher swelling power and solubility at 85 °C.

Hydrothermal liquefaction (HTL) is an efficient technology for converting biomass to platform compounds. It has great potential for reducing the dependence on fossil fuels. The HTL of waste biomass has been extensively studied in recent years due to both its environmental and economic benefits. However, most woody waste contains a large amount of cellulose, and it is difficult to be sufficiently decomposed to valuable chemicals. Phycocyanin, a key component of algae, is easily degraded under high-temperature liquefaction conditions. In this work, focusing on bio-oil generation properties, the co-liquefaction characteristics and synergistic mechanisms of α-cellulose and phycocyanin were explored. The findings revealed a maximum bio-oil yield of 33.1 wt% under the optimal conditions (300 °C for 40 min), with a notable positive synergistic effect of 13.5 wt%. Chemical composition analysis indicated distinct compositional differences between the bio-oils derived from individual and dual feedstock. The amounts of pyridine and pyrimidine compounds increased due to the enhanced co-liquefaction. The results also highlighted the influence of temperature on the degree of conversion and product distribution. Finally, preliminary chemical reaction pathway was elucidated, underscoring the potential of integrating microalgae and woody biomass for enhanced bio-oil production.

The impregnability of Portuguese maritime pine (Pinus pinaster Ait.) subjected to microwave (MW) drying was tested, and the hydrophobicity, anti-swelling efficiency (ASE), and water repellence efficiency (WRE) were evaluated. Small wood heartwood samples of Portuguese maritime pine and two distinct MW treatment settings were employed. The levels of ASE and WRE of the wood elements were evaluated throughout four cycles of drying in an oven and soaking in water. Because of MW applied energy, the wood pine samples were satisfactorily impregnated with the preservative product. Regarding the absolutely dry densities of the samples, very subtle reductions were measured, and they were statistically equivalent to the average density of the non-MW-treated group. Slight improvements were identified in the WRE values of wood samples dried in the microwave. In terms of ASE, both MW-treated groups had a statistically significant increase. The MW treatment decreased the volumetric swelling of the maritime pine wood specimens. Hence, this study raises new insights and previously unexplored paths that can contribute to the expansion and greater application of MW technology in maritime pine and other species.

Activated carbon (AC) materials, renowned for their high specific surface area, excellent conductivity, and customizable functional groups, are widely employed as catalyst carriers. However, enhancing the activity of Ru-based catalysts supported on AC (Ru/AC) for ammonia decomposition remains a challenge. In this study, commercial AC was utilized as a substrate, with glucose and urea employed as modifiers. Specifically, the surface of the AC was modified via a hydrothermal pyrolysis method, resulting in the successful post-treatment in situ co-doping of nitrogen (AC-GN). Experimental results revealed that Ru/AC-GN exhibited a hydrogen production rate 46% higher than that of Ru/AC at 475 °C, indicating improved activity and stability. The characterization of AC-GN demonstrated that nitrogen doping primarily occurred on the external surface and macropores of the AC, increasing the nitrogen content in the carrier, particularly pyrrolic nitrogen content, while preserving the original structural and morphological integrity of the AC. The enhanced dispersion of Ru, combined with the improved electronic transmission capabilities and strengthened interactions between the metal and the modified carrier, were identified as pivotal factors contributing to the enhanced low-temperature efficacy of Ru/AC-GN. This paper presents a novel direction for the large-scale preparation of efficient catalysts for ammonia decomposition.

Reaction wood is a wood defect arising during the growth of the tree in the part of the trunk that is under tension (hardwood tree species) or compression (coniferous tree species). Beech (Fagus sylvatica L.) tension wood has different anatomical and chemical characteristics than normal (opposite) wood. The difference in density is conditioned by the percentage of the gelatinous layer (G-layer). Fibre cells in reaction beech wood have a different cell wall structure and a different chemical composition. Tension wood cannot be detected by the naked eye. It is only possible to assume its occurrence based on the macroscopic characteristics of the logs, such as a woolly surface, taper or eccentric pith, and so forth. However, these are imprecise and unreliable methods that have minimal effectiveness, especially when shortening the length of the log for cut-outs. This study aimed to create a unique chemical reagent for the detection of tension wood in logs and timber and wood products immediately. The present research can contribute to the mitigation of flaws resulting from the reaction of wood in timber production while addressing noticeable constraints in manufacturing, such as energy resources and the availability of wood raw materials. This can be achieved through the efficient identification of reaction wood in materials. The colour change is only temporary and will fade over time. After the chemical reagent has dried on the surface, the surface can be milled. The colour change extends to a depth of approx. of 3 to 5 mm.

Corn straw-based board has great potential for the protection of forest resources, waste recycling, and sustainable economic development. However, corn stalk-based board has poor mechanical properties due to its short fiber length and poor water resistance because of the presence of numerous hydrophilic hydroxyl functional groups in its structure. Natural mycelium originating from waste Pleurotus ostreatus substrate is a hydrophobic bio-adhesive. In the present study, formaldehyde-free corn stalk/P. ostreatus substrate bio-composites were prepared using the hot-pressing technique without the addition of any chemical adhesive. The mechanical properties and water resistance of the prepared bio-composites were excellent. The highest internal bonding strength (IBS) of 2.16 MPa and the minimum thickness swelling (TS) of 18.3% were observed, which are beyond the national standards for particleboard in China. These bio-composites were prepared using a simple, green, and convenient manufacturing method to promote their popularization and application. The method may, therefore, be used as a novel technical measure to resolve the problem of overuse of forestry resources and waste disposal.

Cross-laminated timber (CLT) fails in the outermost tensile lamina under bending loads, or rolling shear failure occurs in the Minoir direction lamina.  This study investigated the effect of lamina width (90 mm, 120 mm), modulus of elasticity (MOE), and placement of major direction lamina on the shear strength of Larix kaempferi Carr CLT. The shear test was conducted using the short span bending test. Results showed that the specimen with 90 mm width of lamina underwent rolling shear failure at the minor direction lamina. The specimen with 120 mm width of lamina had suppressed rolling shear failure and failed at the outermost tensile lamina, which resulted in 52% higher shear strength compared to the 90 mm width specimen. CLT with high MOE placed in the outermost tensile lamina had increased shear strength. The specimen with four laminas in the major direction had both the highest strength and the lowest reliability due to the high standard deviation. This suggested that the width of the larch lamina and the MOE affect the strength of CLT. The CLT strength obtained using the FEA and the theoretical analysis were compared with the measured strength values.

A continually increasing demand for papermaking materials and simultaneously growing disproportion between the request for fiber and the limited resources of wood have forced scientists and the papermaking industry to search for the new sources of fibrous raw materials. A new promising set of raw materials for papermaking comes from energy crops. This paper presents Sida hermaphrodita Rusby L., as a non-woody raw material for papermaking. From the studies of chemical composition, it follows that cellulose content of more than 40% characterizes phloem of stems and branches, whereas in xylem exhibits more than 32%. The lowest is the concentration of cellulose in leaves and flowers of Sida. The content of lignin is lower than 24% and 16% in stem xylem and phloem, respectively. In Sida, hemicelluloses and mineral substances stand for being not more than 30% and 2%, respectively. The morphology of Sida cells is similar to hardwood, with fiber length of 0.383, 0.470 and 1.025 mm for parenchyma, xylem, and phloem, respectively. The chemical composition of Sida hermaphrodita together with its morphological characteristics make this raw material suitable for a production of papers intended for printing, writing and tissue.